ISO 2859-0:1995
$19.50
Sampling procedures for inspection by attributes — Part 0: Introduction to the ISO 2859 attribute sampling system
| Published By | Publication Date | Number of Pages |
| ISO | 1995-08 | 63 |
Explains the terms used in acceptance sampling, describes the various schemes and plans, gives practical advice on sampling inspection and discusses some of the theoretical aspects. This edition cancels and replaces ISO 2859.
Related products
-
AS 1199.0:2003 (R2016)
Sampling procedures for inspection by attributes – Introduction to the ISO 2859 attribute sampling system…
-
BS AU 259:1995
Specification for components for commercial vehicles and buses. Cross-tooth propeller shaft flanges, type T Published…
-
BS 5084-1:1975
Specification for magnetic tape for instrumentation applications – Physical properties and test methods Published By…
-
BS ISO 5-4:1995
Photography. Density measurements – Geometric conditions for reflection density Published By Publication Date Number of…
-
BS EN ISO 4491-2:1999
Metallic powders. Determination of oxygen content by reduction methods – Loss of mass on hydrogen…
-
BS ISO/IEC 8859-10:1992:1993 Edition
Information technology. 8-bit single-byte coded graphic character sets – Latin alphabet No. 6 Published By…
-
BS ISO/IEC 8859-10:1998
Information technology. 8-bit single-byte coded graphic character sets – Latin alphabet No. 6 Published By…
-
BS 6001-5:2000
Sampling procedures for inspection by attributes – Procedures for assessment of stated quality levels Published…
-
BS ISO/IEC 8859-14:1998:1999 Edition
Information technology. 8-bit single-byte coded graphic character sets – Latin alphabet No. 8 (Celtic) Published…
-
BS 6001-3:1986
Sampling procedures for inspection by attributes – Specification for skip-lot procedures Published By Publication Date…
-
BS EN ISO 2702:1995
Heat-treated steel tapping screws. Mechanical properties Published By Publication Date Number of Pages BSI 1995…
-
BS 6001-0:2006
Sampling procedures for inspection by attributes – Introduction to the BS 6001 (ISO 2859) series…
-
BS 7859:1996
Natural gas. Calculation of calorific values, density, relative density and Wobbe index from composition Published…
-
BS 6001-1:1991
Sampling procedures for inspection by attributes – Specification for sampling plans indexed by acceptable quality…
-
BS EN ISO 10545-10:1997
Ceramic tiles – Determination of moisture expansion Published By Publication Date Number of Pages BSI…
-
BS EN ISO 7051:1995
Specification for cross-recessed raised countersunk (oval) head tapping screws Published By Publication Date Number of…
-
BS 903-A59:1990
Physical testing of rubber – Methods using plastimeters Published By Publication Date Number of Pages…
-
BS EN ISO 5620-1:1997
Shipbuilding and marine structures. Filling connection for drinking water tanks – General requirements Published By…
-
BS EN 27501-1:1993
Identification cards. Machine readable travel documents – Machine readable passport Published By Publication Date Number…
-
BS EN ISO 2858:2010:2011 Edition
End-suction centrifugal pumps (rating 16 bar). Designation, nominal duty point and dimensions Published By Publication…
-
BS ISO 10884:1995:1996 Edition
Manually portable brush-cutters and grass trimmers with internal combustion engine. Determination of sound power levels.…
-
BS ISO/IEC 10589:1992
Information technology. Telecommunications and information exchange between systems. Intermediate system to Intermediate system intra-domain routeing…
-
BS EN ISP 10613-7:1997:1995 Edition
Information technology. International standardized profile RA. Relaying the connectionless-mode network service – PSDN subnetwork-dependent, media-dependent…
-
BS 7455-9:1994
Analysis of nickel alloys by flame atomic absorption spectrometry – Method for determination of vanadium…
-
BS EN ISO 7346-1:1998
Water quality. Determination of the acute lethal toxicity of substancesto a freshwater fish [Brachydanio rerio…
-
BS EN ISO 7346-3:1998
Water quality. Determination of the acute lethal toxicity of substancesto a freshwater fish [Brachydanio rerio…
-
BS EN ISO 2060:1995
Textiles. Yarn from packages. Determination of linear density (mass per unit length) by the skein…
-
BS 7431:1991
Method for assessing solar water heaters. Elastomeric materials for absorbers, connecting pipes and fittings Published…
-
BS 6001-2:1993
Sampling procedures for inspection by attributes – Specification for sampling plans indexed by limiting quality…
-
BS ISO 4433-2:1997:1998 Edition
Thermoplastics pipes. Resistance to liquid chemicals. Classification – Polyolefin pipes Published By Publication Date Number…
-
BS 4586:1992
Specification for spiral wire reinforced rubber covered hydraulic hoses and hose assemblies Published By Publication…
-
BS 6001-1:1999+A1:2011
Sampling procedures for inspection by attributes – Sampling schemes indexed by acceptance quality limit (AQL)…
-
BS EN ISO 7346-2:1998
Water quality. Determination of the acute lethal toxicity of substancesto a freshwater fish [Brachydanio rerio…
-
BS G 259:1996
Aircraft equipment. Environmental and operating conditions for airborne equipment. Humidity, temperature and pressure tests Published…
-
BS EN ISO 10211-1:1996:2003 Edition
Thermal bridges in building construction. Heat flows and surface temperatures – General calculation methods Published…
-
BS EN 61318:2008
Live working. Conformity assessment applicable to tools, devices and equipment Published By Publication Date Number…
-
BS 6001-3:1993
Sampling procedures for inspection by attributes – Specification for skip-lot procedures Published By Publication Date…
-
BS EN 24492:1993
Metallic powders, excluding powders for hardmetals. Determination of dimensional changes associated with compacting and sintering…
-
BS 6001-0:1996
Sampling procedures for inspection by attributes – Introduction to the BS 6001 attribute sampling system…
-
BS 4848-2:1991
Hot-rolled structural steel sections – Specification for hot-finished hollow sections Published By Publication Date Number…
