🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN 754-1:2016

BS EN 754-1:2016

$102.76

Aluminium and aluminium alloys. Cold drawn rod/bar and tube – Technical conditions for inspection and delivery

Published By Publication Date Number of Pages
BSI 2016 22
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This European Standard specifies the technical conditions for inspection and delivery of aluminium and aluminium alloy cold drawn rod/bar and tube for general engineering applications.

This document applies to products which are extruded and then cold drawn.

This document does not apply to:

  • forging stock ( EN 603 ),

  • products delivered in coils ( EN 13958 ),

  • coiled tubes cut to length ( EN 13958 ).

PDF Catalog

PDF Pages PDF Title
4 Contents Page
5 European foreword
6 1 Scope
2 Normative references
7 3 Terms and definitions
4 Ordering information
9 5 Requirements
5.1 Production and manufacturing processes
5.2 Quality control
5.3 Chemical composition limits
5.4 Mechanical properties
5.5 Freedom from surface defects
10 5.6 Tolerances on dimensions and form
5.7 Stress corrosion cracking resistance
5.8 Additional requirements
6 Test procedures
6.1 Sampling
6.1.1 Samples for chemical analysis
6.1.2 Specimens for mechanical testing
6.1.2.1 Location and size
11 6.1.2.2 Orientation
6.1.2.3 Identification
6.1.2.4 Preparation
6.1.2.5 Number
12 6.1.3 Test pieces for tensile test
6.1.3.1 Identification
6.1.3.2 Machining
6.1.3.3 Number, type and location of test pieces
6.2 Test methods
6.2.1 Chemical composition limits
6.2.2 Tensile testing
6.2.3 Brinell hardness testing
6.2.4 Measurement of dimensions
6.2.5 Surface finish
13 6.2.6 Resistance to stress corrosion cracking
6.2.7 Additional tests
6.3 Re-tests
6.3.1 Chemical composition limits
6.3.2 Mechanical properties
6.3.3 Other properties
14 7 Inspection documents
8 Marking of products
9 Packaging
10 Arbitration
15 Annex A (normative) Location of test pieces
A.1 Round, square and hexagonal bar
A.1.1 For diameter (D) or width across flats (S) up to and including 40 mm:
Figure A.1 — Round, square and hexagonal bar
A.1.2 For diameter (D) or width across flats (S) over 40 mm:
Figure A.2 — Round, square and hexagonal bar
16 A.2 Rectangular bar
A.2.1 For thickness up to and including 12,5 mm:
A.2.2 For thickness (T) over 12,5 mm and up to and including 40 mm:
Figure A.3 — Rectangular bar
A.2.3 For thickness (T) exceeding 40 mm:
Figure A.4 — Rectangular bar
17 A.3 Tube
Table A.1 — Test piece requirements for tubes
18 Annex B (normative) Resistance to stress-corrosion cracking for alloy EN AW-7075 in tempers T73, T7351, T73510 and T73511 – Electrical conductivity
Table B.1 — Lot acceptance criteria on tempers T73, T7351, T73510 and T73511 for alloy EN AW-7075
19 Bibliography

Related products

BS EN 754-1:2016
$102.76