ISO 494:2009
$13.00
Cylindrical shank twist drills — Long series
| Published By | Publication Date | Number of Pages |
| ISO | 2009-03 | 10 |
ISO 494:2009 specifies the dimensions of cylindrical shank twist drills, having working lengths in the long series.
Related products
-
BS ISO 491:2002
Cinematography. 35 mm motion-picture film and magnetic film. Cutting and perforating dimensions Published By Publication…
-
BSI PD CEN/TR 15592:2007
Health services. Quality management systems. Guide for the use of EN ISO 9004:2000 in health…
-
ISO 492:2002
Rolling bearings — Radial bearings — Tolerances Published By Publication Date Number of Pages ISO…
-
BS EN ISO 4934:2003 2004
Steel and iron. Determination of sulfur content. Gravimetric method Published By Publication Date Number of…
-
ISO 294-1:1996/Amd 1:2001
Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles,…
-
BS EN ISO 294-4:2019
Plastics. Injection moulding of test specimens of thermoplastic materials – Determination of moulding shrinkage Published…
-
ISO 3664:2009
Graphic technology and photography — Viewing conditions Published By Publication Date Number of Pages ISO…
-
BS EN ISO 294-4:2003 2010
Plastics. Injection moulding of test specimens of thermoplastic materials – Determination of moulding shrinkage Published…
-
BSI 19/30406064 DC:2019 Edition
BS ISO 4948. Classification of steel based on chemical composition Published By Publication Date Number…
-
AS 7240.11:2008
Fire detection and alarm systems – Manual call points (ISO 7240-11:2005, MOD) Published By Publication…
-
AS 7240.5:2004 (R2016)
Fire detection and alarm systems – Point type heat detectors (ISO 7240-5:2003, MOD) Published By…
-
BS ISO 4094:2005
Paper, board and pulps. International calibration of testing apparatus. Nomination and acceptance of standardizing and…
-
ISO 15161:2001
Guidelines on the application of ISO 9001:2000 for the food and drink industry Published By…
-
ISO 294-3:2002/Amd 1:2006
Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates…
-
ISO 26909:2009
Springs — Vocabulary Published By Publication Date Number of Pages ISO 2009-07 94
-
AS 5013.10:2009
Food microbiology – Microbiology of food and animal feeding stuffs – Horizontal method for the…
-
D14.8M:2009 (ISO/TR 17844:2004 Idt) Standard Method for Avoidance of Cold Cracks
D14.8M:2009 (ISO/TR 17844:2004 Idt) Standard Method for Avoidance of Cold Cracks Published By Publication Date…
-
ISO 15553:2006
Water quality — Isolation and identification of Cryptosporidium oocysts and Giardia cysts from water Published…
-
ISO/IEC 14165-414:2007
Information technology — Fibre Channel — Part 414: Generic Services — 4 (FC-GS-4) Published By…
-
BS EN ISO 694:2001
Ships and marine technology. Positioning of magnetic compasses in ships Published By Publication Date Number…
-
AS ISO 13822:2005 (R2016)
Basis for design of structures – Assessment of existing structures (ISO 13822:2001, MOD) Published By…
-
ISO 294-1:1996/Amd 2:2005
Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles,…
-
ISO 4094:2005
Paper, board and pulps — International calibration of testing apparatus — Nomination and acceptance of…
-
ISO 7494-2:2003
Dentistry — Dental units — Part 2: Water and air supply Published By Publication Date…
-
ISO 4934:2003
Aciers et fontes — Dosage du soufre — Méthode gravimétrique Published By Publication Date Number…
-
ISO 22901-1:2008
Road vehicles — Open diagnostic data exchange (ODX) — Part 1: Data model specification Published…
-
ISO 13623:2009
Petroleum and natural gas industries — Pipeline transportation systems Published By Publication Date Number of…
-
ISO/IEC 14776-414:2009
Information technology — Small Computer System Interface (SCSI) — Part 414: SCSI Architecture Model-4 (SAM-4)…
-
BS EN ISO 4945:2009 2010
Steel. Determination of nitrogen content. Spectrophotometric method Published By Publication Date Number of Pages BSI…
-
ISO 694:2000
Ships and marine technology — Positioning of magnetic compasses in ships Published By Publication Date…
-
BS ISO 492:2002
Rolling bearings. Radial bearings. Tolerances Published By Publication Date Number of Pages BSI 2002 32
-
BSI 19/30361531 DC:2019 Edition
BS ISO 4948. Classification of steel based on chemical composition Published By Publication Date Number…
-
ISO 294-4:2001
Plastics — Injection moulding of test specimens of thermoplastic materials — Part 4: Determination of…
-
BS EN ISO 449:2000
Ships and marine technology. Magnetic compasses, binnacles and azimuth reading devices. Class A Published By…
-
BS EN ISO 7494-1:2005:2007 Edition
Dentistry. Dental units – General requirements and test methods Published By Publication Date Number of…
-
ISO 491:2002
Cinematography — 35 mm motion-picture film and magnetic film — Cutting and perforating dimensions Published…
-
ISO/TS 4949:2003
Steel names based on letter symbols Published By Publication Date Number of Pages ISO 2003-06…
-
ISO 294-3:2002
Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates…
-
BS EN ISO 7494-2:2003
Dentistry. Dental units – Water and air supply Published By Publication Date Number of Pages…
-
BS EN ISO 294-3:2003
Plastics. Injection moulding of test specimens of thermoplastic materials – Small plates Published By Publication…
