{"id":12474,"date":"2024-10-16T21:04:51","date_gmt":"2024-10-16T21:04:51","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/astm-f1974\/"},"modified":"2024-10-24T11:41:47","modified_gmt":"2024-10-24T11:41:47","slug":"astm-f1974","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/astm\/astm-f1974\/","title":{"rendered":"ASTM-F1974"},"content":{"rendered":"

ASTM F1974-09<\/h3>\n

Historical Standard: Standard Specification for Metal Insert Fittings for Polyethylene\/Aluminum\/Polyethylene and Crosslinked Polyethylene\/Aluminum\/Crosslinked Polyethylene Composite Pressure Pipe<\/h4>\n
\n

ASTM F1974<\/h4>\n

Scope<\/strong><\/p>\n

1.1 This specification covers metal insert fittings with split ring and compression nut (compression joint) and metal insert fittings with copper crimp rings (crimp joint) for four sizes of composite pressure pipe. These fittings are intended for use in 125 psi (690 kPa) cold- and hot-water distribution systems operating at temperatures up to and including 180 \u00b0<\/span>F (82 \u00b0<\/span>C). (When used in polyethylene\/aluminum\/polyethylene systems the maximum operating temperature is limited by the pipe to 140 \u00b0<\/span>F (60 \u00b0<\/span>C) and where applicable 180\u00b0<\/span>F (82\u00b0<\/span>C)). Included are the requirements for materials, workmanship, burst pressure, sustained pressure, excessive temperature and pressure, temperature cycling tests, and markings to be used on the fittings and rings. The fittings covered by this specification are intended for use in potable water distribution systems for residential and commercial applications, water service, underground irrigation systems, and radient panel heating systems, baseboard, snow- and ice-melt systems, and gases that are compatible with the composite pipe and fittings.<\/p>\n

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.<\/p>\n

Note<\/span> 1\u2014The tables show the \u201c<\/span>nominal size\u201d<\/span> in millimetres with the inch size in parentheses. This exception is made to harmonize the \u201c<\/span>nominal size\u201d<\/span> with the two pipe standards, F1281 and F1282.<\/p>\n

1.3 The following precautionary caveat pertains only to the test method portion, Section 9, of this specification.<\/span> This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.<\/span><\/span><\/p>\n

Keywords<\/strong><\/p>\n

cold and hot water distribution; copper crimp rings; crosslinked polyethylene; metal insert fittings; polyethylene; PE\/AL\/PE; PEX\/AL\/PEX; PAP; Composites–piping applications (specifications); Copper crimp rings–specifications; Crosslinked polyethylene (PEX) pipe\/tube–specifications; Hot water supply\/distribution systems–specifications; Metal insert fittings–specifications; PAP; Cold water supply\/distribution systems–specifications; PE\/AL\/PE pipe; PEX\/AL\/PEX pipe\/tube; Polyethylene (PE) pipe–specifications<\/p>\n

ICS Code<\/strong><\/p>\n

ICS Number Code 23.040.40 (Metal fittings)<\/p>\n

DOI:<\/strong> 10.1520\/F1974-09<\/p>\n<\/div>\n

PDF Catalog<\/h4>\n\n\n\n\n\n\n\n\n\n
PDF Pages<\/th>\nPDF Title<\/th>\n<\/tr>\n
1<\/td>\nScope
Referenced Documents <\/td>\n<\/tr>\n
2<\/td>\nTerminology
Classification
Materials and Manufacture
Performance Requirements
TABLE 1 <\/td>\n<\/tr>\n
3<\/td>\nDimensions
Workmanship, Finish and Appearance
TABLE 2 <\/td>\n<\/tr>\n
4<\/td>\nTABLE 3
TABLE 4 <\/td>\n<\/tr>\n
5<\/td>\nTest Methods
Retests
TABLE 5 <\/td>\n<\/tr>\n
6<\/td>\nProduct Marking
Keywords
X1. CRIMP GAGE
X1.1
X1.2
X1.3 Use of the Crimp Gage <\/td>\n<\/tr>\n
7<\/td>\nFIG. X1.1 <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":"

F1974-09 Standard Specification for Metal Insert Fittings for Polyethylene\/Aluminum\/Polyethylene and Crosslinked Polyethylene\/Aluminum\/Crosslinked Polyethylene Composite Pressure Pipe<\/b><\/p>\n\n\n\n\n
Published By<\/td>\nPublication Date<\/td>\nNumber of Pages<\/td>\n<\/tr>\n
ASTM<\/b><\/a><\/td>\n2009<\/td>\n7<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":12475,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[350,2637],"product_tag":[],"class_list":{"0":"post-12474","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-23-040-40","7":"product_cat-astm","9":"first","10":"instock","11":"sold-individually","12":"shipping-taxable","13":"purchasable","14":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/12474","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/12475"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=12474"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=12474"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=12474"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}