Shopping Cart

No products in the cart.

ASME BPVC III 2 2017

$377.00

ASME BPVC – III – 2 -2017 BPVC Section III, Rules for Construction of Nuclear Facility Components, Division 2, Code for Concrete Containments

Published By Publication Date Number of Pages
ASME 2017
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

None

PDF Catalog

PDF Pages PDF Title
55 CC-2222.1-1 Required Limits of Alkali-Silica Reactive Materials in Concrete Aggregates
56 CC-2231.3-1 Required Minimum Levels of Cementitious Materials
57 CC-2231-1 Concrete Properties
CC-2231.7.1-1 Exposure Categories and Classes
58 CC-2231.7.2-1 Requirements for Concrete by Exposure Class
59 CC-2231.7.3-1 Requirements for Concrete Subject to Exposure Class F3
CC-2231.7.4-1 Requirements for Establishing Suitability of Cementitious Materials Combinations Exposed to Water-Soluble Sulfate
CC-2231.7.5-1 Concrete Air Content for Various Sizes of Coarse Aggregates
60 CC-2233.1.2-1 Modification Factor for Standard Deviation When Less Than 30 Tests Are Available
CC-2233.2.1-1 Required Average Compressive Strength When Data Are Available to Establish a Sample Standard Deviation
61 CC-2233.2.2-1 Required Average Compressive Strength When Data Are Not Available to Establish a Standard Deviation
63 CC-2243.3.2-1 Schupack Pressure Bleed Test Limits
64 CC-2310-1 Maximum Dimensions of Obstruction or Interruptions of Bar Deformations and Nonplanar Features of the Bearing Face
68 CC-2438.4.2-1 Analysis Limits of Permanent Coating Material for CRV Prestressing
71 CC-2462-1 Manufacturer’s Record of Tendon Performance Qualification Tests
72 CC-2465-1 Record of Mechanical Test Results Obtained From Tendon Performance Qualification Tests
73 CC-2521.1-1 Exemptions From Impact Testing Under CC-2521.1(h)
74 CC-2521.1-1 Determination of Permissible Lowest Service Metal Temperature
75 CC-2521.1-1M Determination of Permissible Lowest Service Metal Temperature
76 CC-2524.2-1 Required Cv Lateral Expansion Values for Liner Material Other Than Bolting
77 CC-2524.2-2 Required Cv Energy Values for Liner Material Other Than Bolting
CC-2524.3(a)-1 Required Cv Values for Bolting Material Tested in Accordance With CC-2524.3(a)
CC-2524.3(b)-1 Required Cv Values for Bolting Material Tested in Accordance With CC-2524.3(b) and CC-2524.4
78 CC-2524.4-1 Required Cv Energy Values for Liner Material for the Overpressure Test
87 CC-2613.1-1 Sampling of Welding Materials for Chemical Analysis
88 CC-2613.2-1 Welding Material Chemical Analysis
89 CC-2613.3.1-1 Delta Ferrite Content
90 CC-2620-1 Dimensions and Tolerances of Standard Studs
91 CC-2620-2 Typical Tensile Test Fixture
CC-2620-3 Bend Testing Device
92 CC-2620-4 Typical Device for Bend Testing of Small Studs
93 CC-2623.2-1 Strength Requirements for Studs
97 CC-3136.6-1 Classification of Forces in Concrete Containments for Steel Reinforcing and Concrete Allowable Stresses
99 CC-3230-1 Load Combinations and Load Factors
100 CC-3421-1 Allowable Compression Stresses for Factored Loads
107 CC-3431-1 Allowable Compression Stresses for Service Loads
118 CC-3720-1 Liner Plate Allowables
119 CC-3730-1 Liner Anchor Allowables
120 CC-3831-1 Illustration of Welded Joint Locations Typical of All Categories
122 CC-3840-1 Tapered Transition Sections
127 CC-4323-1 Allowable Bend Configuration
CC-4322-1 Minimum Diameter of Bend
131 CC-4333-1 Tensile Requirements for Mechanical Reinforcing Bar Splices, Mechanically Headed Deformed Bars, and Welded Joints
135 CC-4462-1 Time Limits for Grouting: Permissible Intervals Between Prestressing Steel Installation and Grouting Without Use of Corrosion Protection
138 CC-4523-1 Maximum Allowable Offset in Final Welded Joints
142 CC-4534-1 Required Torque for Testing Studs
143 CC-4534-1 Typical Torque Testing Device
144 CC-4542.2-1 Typical Category D Joints for Nozzle Diameters Over NPS 3 (DN 80)
146 CC-4542.2-2 Typical Category D Joints for Nozzle Diameters NPS 3 (DN 80) and Less
148 CC-4542.2-3 Typical Category E Joints
149 CC-4542.2-4 Typical Category F Joints
CC-4542.2-5 Typical Category G Joints
150 CC-4542.2-6 Typical Category H Joints
151 CC-4542.2-7 Typical Category J Joints
CC-4542.8.1-1 Maximum Thicknesses Permitted
152 CC-4542.9-1 Fillet and Socket Weld Dimensions
155 CC-4543.6-1 Weld Joint Producing Through‐Thickness Loading
CC-4543.6-2 Special Deposition Technique for Weld Joint Producing Through‐Thickness Loading (Typical)
157 CC-4552-1 Mandatory Requirements for Postweld Heat Treatment (PWHT) of Welds
CC-4552-2 Exemptions to Mandatory PWHT
158 CC-4552-3 Alternative PWHT Temperatures
165 CC-5200-1 Minimum Testing Frequencies for Concrete Constituents and Concrete
183 D2-I-1.2 Material for Containment Prestressing Systems
D2-I-2.2 Material for Containment Liners
187 D2-I-2.3 Material for Embedment Anchors
200 D2-V-4100-1 Minimum Levels of Capability for Functions
207 D2-VIII-1410-1 Filler Metal Requirements
208 D2-VIII-1420-1 Typical Direct Butt Splices
210 D2-VIII-1430-1 Minimum Preheat and Interpass Requirements
212 D2-VIII-1620-1 Radiograph Acceptance Criteria
225 D2-D-1230-1 Measurements of Local Dimensions per D2-F-1230
226 D2-D-1320-1 Measurement Points per D2-F-1320
227 D2-D-1330-1 Measurement Points per D2-F-1330
231 D2-F-1220-1 Standard Fabricating Tolerances for Bar Sizes #3 (10 mm) Through #11 (35 mm)
234 D2-F-1230-1 Standard Fabricating Tolerances for Bar Sizes #14 (43 mm) and #18 (57 mm)
236 D2-F-1320-1 Location of Reinforcement
ASME BPVC III 2 2017
$377.00