🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
ASTM-B216:2010 Edition(Redline)

ASTM-B216:2010 Edition(Redline)

$28.60

B216-10 Standard Specification for Tough-Pitch Fire-Refined Copper—Refinery Shapes (Redline)

Published By Publication Date Number of Pages
ASTM 2010 7
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Abstract

This specification establishes the requirements for tough-pitch fire-refined copper wire bars, cakes, slabs, and billets for fabricating into wrought products and ingot and ingot bars for use in the manufacture of copper and copper alloy castings. This copper is not intended for electrical purposes. Any copper may be used that will yield a product with a chemical composition conforming to the requirements specified. The chemical composition test shall be made to conform with the product specification requirements.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

Significance and Use

Calculated values shall be rounded to the nearest unit in the last right-hand significant digit used in expressing the limiting value in accordance with the rounding method in Practice E29 .

1. Scope

1.1 This specification establishes the requirements for tough-pitch fire-refined copper wire bars, cakes, slabs, and billets for fabricating into wrought products and ingot and ingot bars for use in the manufacture of copper and copper alloy castings. This copper is not intended for electrical purposes.

1.2 Copper under this specification corresponds to the designation “ FRTP ” (UNS C12500) as shown in Classification B224 . This copper may also be used to produce copper, corresponding to the designation “ DPTE ” (UNS C14520).

1.3 Although this specification includes certain UNS designations as described in Practice E527 , these designations are for cross reference only and are not specification requirements. Therefore, in case of conflict, this ASTM specification shall govern.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5 The following safety hazard caveat pertains only to the test method described in the annex of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

A1.1.1 This test method covers the analysis of antimony, arsenic, bismuth, lead, nickel, selenium, and tellurium in tough-pitch fire-refined copper.

A1.1.2 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

B224 Classification of Coppers E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications E50 Practices for Apparatus, Reagents, and Safety Considerations for Chemical Analysis of Metals, Ores, and Related Materials E53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry E255 Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)

Keywords

fire refined copper; refinery shapes; tough pitch copper; Copper (refined/refinery shapes)–specifications; Tough pitch coppers; UNS C12500 (fire-refined tough pitch copper, FRTP); UNS C14200 (phosphorus deoxidized copper, arsenical (DPA)); UNS C14500 (phosphorus deoxidized copper, tellurium bearing);

ICS Code

ICS Number Code 77.150.30 (Copper products)

DOI: 10.1520/B0216-10 ASTM International is a member of CrossRef.

Citing ASTM Standards

[Back to Top]

Related products

ASTM-B216
$28.60