ASTM-D3032 2021(Redline)

$58.50

D3032-21a Standard Test Methods for Hookup Wire Insulation (Redline)

Published By	Publication Date	Number of Pages
ASTM	2021

Guaranteed Safe Checkout

Categories: 29.060.10 - Wires, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

ASTM D3032-21a

Redline Standard: Standard Test Methods for Hookup Wire Insulation

ASTM D3032

Scope

1.1 These test methods cover procedures for testing hookup wire.

1.2 For the purposes of these test methods, hookup wire insulation includes all components of the insulation system used on single insulated conductors or an assembly of single insulated conductors such as a cable bundle and harness or flat ribbon cable. The insulating materials include not only the primary insulation over the conductor, but also insulating jackets over shielded constructions.

1.3 These test methods and their locations are as follows:

1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.

1.5 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not, by itself, incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.

1.6 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.

1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 17.1.3, 24.4, and Note 18.

1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Keywords

ambient temperature; arcing; arc-propagation; arc-tracking; atmospheric pressure; breakdown voltage; cable; circuit breakers; current limiting; cuts; degradation; dropping apparatus; dry-arcing; electrical insulation; electrolyte; extinction voltage; flame propagation; flame spread; flame test; flammability; hookup wire; insulation thickness; moisture; open-circuit detection; partial discharge; power supply; safe voltage; scintillation; service condition; short-circuit detection; shutdown equipment; track resistant; tracking; transportation vehicles; voltage rating; wet; wire abrasion; wire chafing; wire insulation;

ICS Code

ICS Number Code 29.060.10 (Wires)

DOI: 10.1520/D3032-21A

Additional information

Concentricity	25
High Temperature Shock	23
Voltage Rating of Hook-Up Wire	Annex A1
Axial Stability (Longitudinal Change) After Thermal Exposure	20
Capacitance	9 to 11
Crush Resistance	19
Cold Bend Test	25
Bondability of Insulation to Potting Compounds	18
Dielectric Breakdown Voltage	5
Vertical Flame Test B	17.6 – 17.11.4
Vertical Flame Test A	18.5 (Test Method D8354)
Dimensions	14
Vertical Flame	17
Dry-arc Tracking	28
Voltage Withstand Test	8
Dynamic Cut-through	21
Insulation Resistance	6
Partial Discharge (Corona) Inception and Extinction Voltage	24
Surface Resistance	26
Insulation-Continuity Proof Tests	12
Wet Arc-tracking	27
Relative Thermal Life and Temperature Index	13
Tensile Properties	16
Strip Force	26
Fluid Immersion	22
	Section
ICS Codes	29.060.10 - Wires

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-D3032 2021(Redline)

ASTM D3032-21a

Redline Standard: Standard Test Methods for Hookup Wire Insulation

ASTM D3032

Related products