ASTM-D92 2010

$40.63

D92-05a(2010) Standard Test Method for Flash and Fire Points by Cleveland Open Cup Tester

Published By	Publication Date	Number of Pages
ASTM	2010	10

Guaranteed Safe Checkout

Categories: 13.220.40 - Ignitability and burning behaviour of materials and products, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

ASTM D92-05a-Reapproved2010

Historical Standard: Standard Test Method for Flash and Fire Points by Cleveland Open Cup Tester

ASTM D92

Scope

1.1 This test method describes the determination of the flash point and fire point of petroleum products by a manual Cleveland open cup apparatus or an automated Cleveland open cup apparatus.

Note 1—The precisions for fire point were not determined in the current interlaboratory program. Fire point is a parameter that is not commonly specified, although in some cases, knowledge of this flammability temperature may be desired.

1.2 This test method is applicable to all petroleum products with flash points above 79°C (175°F) and below 400°C (752°F) except fuel oils.

Note 2—This test method may occasionally be specified for the determination of the fire point of a fuel oil. For the determination of the flash points of fuel oils, use Test Method D93. Test Method D93 should also be used when it is desired to determine the possible presence of small, but significant, concentrations of lower flash point substances that may escape detection by Test Method D92. Test Method D1310 can be employed if the flash point is known to be below 79°C (175°F).

1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.4 WARNINGMercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s websitehttp://www.epa.gov/mercury/faq.htmfor additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 6.4, 7.1, 11.1.3, and 11.2.4.

Keywords

automated Cleveland open cup; Cleveland open cup; fire point open cup for flash point; flammability; flash point; petroleum products; Cleveland open cup test; Fire testing–petroleum products; Flash point–liquids; Open-cup flash point methods

ICS Code

ICS Number Code 13.220.40 (Ignitability and burning behaviour of materials and products)

DOI: 10.1520/D0092-05AR10

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents
2	Terminology Summary of Test Method Significance and Use Apparatus
3	FIG. 1 FIG. 2 FIG. 3
4	Reagents and Materials Sampling Preparation of Apparatus Calibration and Standardization
5	Procedure
6	Calculations
7	Report Precision and Bias Keywords A1. CLEVELAND OPEN CUP TESTER A1.1 A1.2 A1.3
8	A1.4 A1.5 A1.6 A2. VERIFICATION OF APPARATUS PERFORMANCE A2.1 A2.2 X1. TECHNIQUE TO PREVENT SURFACE SKIN FORMATION WHEN TESTING FLASH POINT OF ASPHALTS BY TEST METHOD D92 X1.1 Introduction X1.2 Materials Required TABLE A2.1
9	X1.3 Procedure FIG. X1.1

Additional information

Standard Title	D92-05a(2010) Standard Test Method for Flash and Fire Points by Cleveland Open Cup Tester
Published Code	ASTM
Publication Date	2010
Pages Count	10
ICS Codes	13.220.40 - Ignitability and burning behaviour of materials and products