šŸ”„šŸ”„ Donā€™t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

šŸ”
ASTM-E2817:2011 Edition

ASTM-E2817:2011 Edition

$58.50

E2817-11 Standard Test Method for Test Fueling Masonry Heaters

Published By Publication Date Number of Pages
ASTM 2011 21
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. Weā€™re here to assist you 24/7.
Email:[email protected]

1.1 This test method covers the fueling and operating protocol for determining particulate matter emissions from solid fuel biomass (cordwood or other densified, binder free biomass fuels) fires in masonry heaters. It may also be used to test other similar appliances (see 3.2.20).

1.2 This test method is applicable to the operation and fueling of masonry heaters during particulate emissions measurement test periods. The prescribed methods and procedures of these protocols are performed on masonry heaters installed and operated in accordance with the builder or manufacturer s specifications.

1.3 In conjunction with Test Method E2515 , this test method provides a protocol for laboratory emissions testing of masonry heaters that is intended to simulate actual use in residential homes and other consumer applications. Since such actual use involves almost solely cordwood fueling, Annex A1, Cordwood Fuel, provides as close a simulation as is currently possible of consumer use, and is recommended for predicting actual consumer emissions performance. For regulatory and other potential uses in comparing relative emissions of various masonry heater products and designs, Annex A2, Cribwood Fueling, and Annex A3, Cribwood Fuel, Top-Down Burn, provide optional additional fueling protocols that substitute dimensional lumber cribs for the cordwood fuel. Data that establish the relationships between the emissions results generated by Annex A2 and Annex A3 and the emissions results generated by Annex A1 are not currently available.

1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

PDF Catalog

PDF Pages PDF Title
1 Scope
Referenced Documents
Terminology
3 Summary of Test Method
Significance and Use
Safety
Equipment and Supplies
4 Calibration and Standardization
5 Procedure
TABLE 1
8 Data Analysis and Calculations
Report
9 Precision and Bias
Keywords
A1. CORDWOOD FUEL
A1.1 Scope
A1.2 Terminology
A1.3 Equipment and Supplies
A1.4 Calibration and Standardization
A1.5 Main Fuel Load Requirements
10 A1.6 Operation
A1.7 Data Analysis and Calculations
TABLE A1.1
11 A2. CRIBWOOD FUELING
A2.1 Crib Construction Procedure
12 FIG. A2.1
TABLE A2.1
13 TABLE A2.2
TABLE A2.3
TABLE A2.4
14 A2.2 Operation
A2.3 Data Analysis and Calculations
TABLE A2.5
TABLE A2.6
15 TABLE A2.7
TABLE A2.8
TABLE A2.9
16 FIG. A2.2
17 FIG. A2.3
18 A3. CRIBWOOD FUEL, TOP-DOWN BURN
A3.1
19 FIG. A3.1
20 A3.2 Operation
A3.3 Data Analysis and Calculations
FIG. A3.2

Related products

ASTM-E2817
$58.50