BS EN 61784-5-19:2013:2014 Edition
$189.07
Industrial communication networks. Profiles – Installation of fieldbuses. Installation profiles for CPF 19
| Published By | Publication Date | Number of Pages |
| BSI | 2014 | 46 |
IEC 61784-5-19:2013 specifies installation profiles for CPF 19 (MECHATROLINK). Each CP installation profile is specified in a separate part of this series of standards. The IEC 61784 series is produced to facilitate the use of communication networks in industrial control systems. This publication is to be read in conjunction with /2.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | English CONTENTS |
| 9 | INTRODUCTION Figures FigureĀ 1 ā Standards relationships |
| 10 | 1 Scope 2 Normative references 3 Terms, definitions and abbreviated terms 4 CPF19: Overview of installation profiles 5 Installation profile conventions |
| 11 | 6 Conformance to installation profiles |
| 13 | Annex A (normative) CP 19/1 (MECHATROLINK-II) specific installation profile A.1 Installation profile scope A.2 Normative references A.3 Installation profile terms, definitions, and abbreviated terms A.3.1 Terms and definitions A.3.2 Abbreviated terms A.3.3 Conventions for installation profiles |
| 14 | A.4 Installation planning A.4.1 General A.4.2 Planning requirements A.4.3 Network capabilities |
| 15 | FigureĀ A.1 ā Topology of CPĀ 19/1 network FigureĀ A.2 ā Network expansion using repeater Tables TableĀ A.1 ā Basic network characteristics for balanced cabling not based on Ethernet |
| 16 | A.4.4 Selection and use of cabling components TableĀ A.2 ā Number of devices and maximum segment length |
| 17 | FigureĀ A.3 ā Structure of cable TableĀ A.3 ā Information relevant to copper cable: fixed cables TableĀ A.4 ā Additional cable specifications |
| 18 | TableĀ A.5 ā Connectors for copper cabling CPs not based on Ethernet |
| 19 | FigureĀ A.4 ā Dimensions of single port device connector FigureĀ A.5 ā Dimensions of dual ports device connector |
| 20 | FigureĀ A.6 ā Dimensions of cable connector FigureĀ A.7 ā Cable connector with inductors |
| 21 | FigureĀ A.8 ā Terminator connection in cable connector housing |
| 23 | A.4.5 Cabling planning documentation A.4.6 Verification of cabling planning specification |
| 24 | A.5 Installation implementation A.5.1 General requirements A.5.2 Cable installation TableĀ A.6 ā Parameters for balanced cables |
| 25 | A.5.3 Connector installation FigureĀ A.9 ā Wiring example |
| 26 | A.5.4 Terminator installation A.5.5 Device installation A.5.6 Coding and labelling A.5.7 Earthing and bonding of equipment and devices and shield cabling FigureĀ A.10 ā Terminator installed in MII cable connector TableĀ A.7 ā Pin assignment and wire colour coding for CPĀ 19/1 connector |
| 27 | A.5.8 As-implemented cabling documentation A.6 Installation verification and installation acceptance test A.6.1 General A.6.2 Installation verification |
| 28 | A.6.3 Installation acceptance test A.7 Installation administration |
| 29 | A.8 Installation maintenance and installation troubleshooting TableĀ A.8 ā Typical problems in a network with balanced cabling |
| 30 | FigureĀ A.11 ā Division of network segment by changing terminator location |
| 31 | Annex B (normative) CP 19/2 (MECHATROLINK-III) specific installation profile B.1 Installation profile scope B.2 Normative references B.3 Installation profile terms, definitions, and abbreviated terms B.3.1 Terms and definitions B.3.2 Abbreviated terms B.3.3 Conventions for installation profiles B.4 Installation planning B.4.1 General B.4.2 Planning requirements |
| 32 | B.4.3 Network capabilities |
| 33 | B.4.4 Selection and use of cabling components TableĀ B.1 ā Network characteristics for balanced cabling based on Ethernet TableĀ B.2 ā Information relevant to copper cable: fixed cables |
| 34 | TableĀ B.3 ā Information relevant to copper cable: cords |
| 35 | FigureĀ B.1 ā Dimensions of IMI device connector TableĀ B.4 ā Connectors for balanced cabling CPs based on Ethernet |
| 36 | FigureĀ B.2 ā Dimensions of IMI cable connector |
| 38 | B.4.5 Cabling planning documentation B.4.6 Verification of cabling planning specification |
| 39 | B.5 Installation implementation B.5.1 General requirements B.5.2 Cable installation TableĀ B.5 ā Parameters for balanced cables |
| 40 | B.5.3 Connector installation B.5.4 Terminator installation B.5.5 Device installation TableĀ B.6 ā Pin assignment and wire colour coding for CPĀ 19/2 connector |
| 41 | B.5.6 Coding and labelling B.5.7 Earthing and bonding of equipment and devices and shield cabling B.5.8 As-implemented cabling documentation B.6 Installation verification and installation acceptance test B.6.1 General B.6.2 Installation verification |
| 42 | B.6.3 Installation acceptance test B.7 Installation administration B.8 Installation maintenance and installation troubleshooting |
| 43 | Bibliography |
