🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN IEC 61169-60:2021

BS EN IEC 61169-60:2021

$167.15

Radio-frequency connectors – Sectional specification for RF coaxial connectors with push on mating. Characteristic impedance 50 Ohm (type SMPM)

Published By Publication Date Number of Pages
BSI 2021 36
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This part of IEC 61169, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for RF coaxial connectors with push-on coupling, typically for use in 50 Ω RF cables or micro-strips in microwave, telecommunication, wireless systems and other fields (SMPM).

It specifies mating face dimensions for general purpose connectors – grade 2, dimensional details of standard test connectors-grade 0, gauging information and tests selected from IEC 61169-1, applicable to all detail specifications relating to series SMPM RF connectors.

This specification indicates recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H.

The SMPM push-on coupling structure series RF coaxial connectors with the characteristic of normative impedance 50 Ω are used with various kinds of RF cables or micro-strips in microwave, telecommunication, wireless systems. The operating frequency limit is up to 65 GHz.

NOTE Imperial dimensions are original dimensions. All undimensioned pictorial configurations are for reference purpose only.

PDF Catalog

PDF Pages PDF Title
2 undefined
5 Annex ZA (normative)Normative references to international publicationswith their corresponding European publications
7 English
CONTENTS
9 FOREWORD
11 1 Scope
2 Normative references
3 Terms and definitions
12 4 Mating face and gauge information
4.1 Dimensions – General connectors – Grade 2
4.1.1 SMPM connector with pin-centre contact
Figures
Figure 1 – SMPM connector with pin-centre contact –Full detent (for dimensions, see Table 1)
Tables
Table 1 – Dimensions of SMPM connector with pin-centre contact full detent
13 Figure 2 – SMPM connector with pin-centre contact –Smooth bore (for dimensions, see Table 2)
Table 2 – Dimensions of SMPM connector with pin-centre contact – Smooth bore
14 4.1.2 SMPM connector with socket-centre contact (see Figure 3)
Figure 3 – SMPM connector with socket-centre contact(for dimensions, see Table 3)
Table 3 – Dimensions of SMPM connector with socket-centre contact
15 4.2 SMPM gauges
4.2.1 SMPM gauge pin for socket-centre contact
Figure 4 – SMPM gauge pin for socket-centre contact(for dimensions, see Table 4)
Table 4 – Dimensions of SMPM gauge pin for socket-centre contact
16 4.2.2 Gauges for outer contact of SMPM connector with socket-centre contact
Figure 5 – SMPM engagement force gauge –Full detent (for dimensions, see Table 5)
17 Table 5 – Dimensions of SMPM engagement force gauge – Full detent
18 Figure 6 – SMPM Separation force gauge –Full detent (for dimensions, see Table 6)
19 Table 6 – Dimensions of SMPM separation force gauge – Full detent
20 Figure 7 – SMPM Engagement force gauge –Smooth bore (for dimensions, see Table 7)
21 Table 7 – Dimensions of SMPM engagement force gauge – Smooth bore
22 Figure 8 – SMPM Separation force gauge –Smooth bore (for dimensions, see Table 8)
23 Figure 9 – SMPM gauge block(for dimensions, see Table 9)
Table 8 – Dimensions of SMPM separation force gauge – Smooth bore
24 5 Quality assessment procedure
5.1 General
5.2 Rating and characteristics (see Clause 5 of IEC 61169-1:2013)
Table 9 – Dimensions of SMPM gauge block
Table 10 – Preferred climatic categories (see IEC 60068-1)
25 Table 11 – Rating and characteristics
27 5.3 Test schedule and inspection requirements
5.3.1 Acceptance tests
5.3.2 Periodic tests
Table 12 – Acceptance tests
28 Table 13 – Periodic tests
29 5.4 Procedures for the quality conformance
5.4.1 Quality conformance inspection
5.4.2 Quality conformance and its maintenance
6 Instructions for preparation of detail specifications (DS)
6.1 General
6.2 Identification of the component
30 6.3 Performances
6.4 Marking, ordering information and related matters
6.5 Selection of tests, test conditions and severities
31 6.6 Blank detail specification pro-forma for type SMPM connector
35 7 Marking
7.1 Marking of component
7.2 Marking and contents of package

Related products

BS EN IEC 61169-60:2021
$167.15