BS EN IEC 61169-63:2020
$167.15
Radio-frequency connectors – Sectional specification. RF coaxial connectors with inner diameter of outer conductor 6,5 mm (0,256 in) with bayonet lock. Characteristic impedance 75 ohms (type BNC75)
| Published By | Publication Date | Number of Pages |
| BSI | 2020 | 36 |
IEC 61169-63:2020 which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for RF coaxial connectors which can preferably be used with RF cables 60096 IEC 50-3 of IEC 60096-2. These connector patterns are for low power, quick connect/disconnect applications using a bayonet type coupling mechanism and are commonly known as type “BNC” with characteristic impedance 75 W. It describes the interface dimensions for general purpose connectors, dimensional details for standard test connectors together with gauging information and the mandatory tests selected from IEC 61169-1, applicable to all DS relating to type BNC connectors with characteristic impedance 75 W. This document indicates the recommended performance characteristics to be considered when writing a DS and covers test schedules and inspection requirements.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 2 | undefined |
| 5 | Annex ZA(normative)Normative references to international publicationswith their corresponding European publications |
| 7 | English CONTENTS |
| 9 | FOREWORD |
| 11 | 1 Scope 2 Normative references 3 Terms and definitions |
| 12 | 4 IEC type designation 5 Interface dimensions – General purpose connectors 5.1 Pin connector Figures Figure 1 – Connector with pin-centre contact Figure 2 – Details of bayonet lock |
| 13 | Figure 3 – Details of alternative coupling grooves Figure 4 – Details of alternative coupling grooves Figure 5 – Details of pin-centre contact |
| 14 | 5.2 Socket connector Tables Table 1 – Dimensions for connector with pin-centre contact |
| 15 | Figure 6 – Connector with socket-centre contact Figure 7 – Details of socket-centre contact Table 2 – Dimensions for connector with socket-centre contact |
| 16 | 6 Mechanical gauges and standard test connectors 6.1 Mechanical gauges 6.1.1 Connectors with pin-centre contact Figure 8 – Gauge for outer contact of pin connector |
| 17 | 6.1.2 Connectors with socket-centre contact Figure 9 – Gauge pin for socket-centre contact Table 3 – Dimensions for gauges for outer contact of pin connector |
| 18 | 6.1.3 Gauge for outer contacts, coupling mechanism and mating face dimensions Figure 10 – Dimensions of gauge for performance test Table 4 – Dimensions for gauge pin for socket-centre contact |
| 19 | 6.2 Standard test connectors 6.2.1 General 6.2.2 Standard test connector with pin contact Figure 11 – Dimensions of connector Table 5 – Dimensions of gauge for performance test |
| 20 | 6.2.3 Standard test connector with socket contact Figure 12 – Dimensions of centre contact Table 6 – Dimensions of centre contact |
| 21 | Figure 13 – Dimensions of connector Figure 14 – Dimensions of centre contact |
| 22 | 7 Outline dimensions 8 Quality assessment procedures 8.1 General 8.2 Ratings and characteristics Table 7 – Dimensions for standard test connector |
| 23 | Table 8 – Preferred climatic categories (see IEC 60068-1) Table 9 – Ratings and characteristics |
| 25 | 8.3 Test schedule and inspection requirements 8.3.1 Acceptance tests |
| 26 | 8.3.2 Periodic tests Table 10 – Acceptance tests Table 11 – Periodic tests |
| 27 | 8.4 Procedures for quality conformance 8.4.1 Quality conformance inspection 8.4.2 Qualification approval and its maintenance 9 Instructions for preparation of detail specifications 9.1 General |
| 28 | 9.2 Identification of the component 9.3 Performance 9.4 Marking, ordering information and related matters 9.5 Selection of tests, test conditions and severities 9.6 Blank detail specification pro-forma for type BNC connector |
| 34 | Bibliography |
