🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
BS EN ISO 15630-1:2019

BS EN ISO 15630-1:2019

$167.15

Steel for the reinforcement and prestressing of concrete. Test methods – Reinforcing bars, rods and wire

Published By Publication Date Number of Pages
BSI 2019 34
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

This document specifies chemical and mechanical test methods and measurement methods of geometrical characteristics applicable to reinforcing bars, rods and wire for concrete.

This document does not cover the sampling conditions that are dealt with in the product standards.

A list of options for agreement between the parties involved is provided in Annex A.

PDF Catalog

PDF Pages PDF Title
2 National foreword
4 European foreword
7 Foreword
8 Introduction
9 1 Scope
2 Normative references
3 Terms, definitions and symbols
11 4 General provisions concerning test pieces
12 5 Tensile test at room temperature
5.1 Test piece
5.2 Test equipment
5.3 Test procedure
13 6 Bend test
6.1 Test piece
14 6.2 Test equipment
6.3 Test procedure
6.4 Interpretation of test results
15 7 Rebend test
7.1 Test piece
7.2 Test equipment
7.2.1 Bending device
7.2.2 Rebending device
7.3 Test procedure
7.3.1 General
16 7.3.2 Bending
7.3.3 Artificial ageing
7.3.4 Rebending
7.4 Interpretation of test results
17 8 Axial force fatigue test
8.1 Principle of test
8.2 Test piece
8.3 Test equipment
18 8.4 Test procedure
8.4.1 Provisions concerning the test piece
8.4.2 Upper force (Fup) and force range (Fr)
8.4.3 Stability of force and frequency
8.4.4 Counting of force cycles
8.4.5 Frequency
8.4.6 Temperature
8.4.7 Validity of the test
9 Chemical analysis
19 10 Measurement of the geometrical characteristics
10.1 Test piece
10.2 Test equipment
10.3 Test procedure
10.3.1 Heights of transverse ribs or depths of indentations
20 10.3.2 Height of longitudinal ribs (a′)
10.3.3 Transverse rib or indentation spacing (c)
10.3.4 Pitch (P)
10.3.5 Part of the circumference without ribs or indentations (Σei)
10.3.6 Transverse rib or indentation angle (β)
10.3.7 Transverse rib flank inclination (α)
21 10.3.8 Width of transverse rib or width of indentation (b)
22 11 Determination of the relative rib or indentation area (fR or fP)
11.1 General
11.2 Measurements
11.3 Calculation of fR
11.3.1 Relative rib area
11.3.2 Simplified formulae
23 11.3.3 Formula used for the calculation of fR
11.4 Calculation of fP
11.4.1 Relative indentation area
24 11.4.2 Simplified formulae
25 11.4.3 Formula used for the calculation of fP
12 Determination of deviation from nominal mass per metre
12.1 Test piece
12.2 Accuracy of measurement
12.3 Test procedure
13 Specialized tests
13.1 Tensile test at elevated temperature
13.1.1 General
13.1.2 Test piece
13.1.3 Test equipment
26 13.1.4 Test procedure
13.2 Tensile test at low temperature
13.2.1 General
13.2.2 Test piece
13.2.3 Test equipment
13.2.4 Test procedure
13.3 Cyclic inelastic load test
13.3.1 Principle of the test
27 13.3.2 Test piece
13.3.3 Test equipment
13.3.4 Test procedure
28 14 Test report
29 Annex A (informative) Options for agreement between the parties involved
30 Bibliography

Related products

BS EN ISO 15630-1:2019
$167.15