BS EN ISO 2063-2:2017 – TC:2020 Edition
$246.62
Tracked Changes. Thermal spraying. Zinc, aluminium and their alloys – Execution of corrosion protection systems
| Published By | Publication Date | Number of Pages |
| BSI | 2020 | 109 |
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 63 | National foreword |
| 65 | European foreword |
| 68 | Foreword |
| 70 | 1 Scope 2 Normative references |
| 71 | 3 Terms and definitions |
| 72 | 4 Requirements for the manufacturer 4.1 General 4.2 Qualification of the manufacturer 4.2.1 Qualification of the equipment 4.2.2 Qualification of supervision personnel 4.2.3 Qualification of spraying personnel 4.2.4 Qualification of test personnel |
| 73 | 4.3 Coating specification for the thermal-sprayed coating 4.4 Assessment of the coating on the basis of reference areas 5 Quality assurance measures for the manufacturer 5.1 General 5.2 Assessment of the design to coatability 5.3 Establishing the manufacturing instructions — Manufacturing sequence plan 5.4 Establishing the thermal spray procedure specification |
| 74 | 5.5 Qualification of the TSPS and scope of the TSPS 5.6 Qualification of the TSPS by a specific job reference qualification 5.7 Special job qualification by performance on mock-ups, if required 6 Manufacturing of thermal-sprayed coatings 6.1 General |
| 75 | 6.2 Preparation of the surface to be coated 6.2.1 Masking of areas not to be coated 6.2.2 Preparation of the surface to be coated by blasting 6.2.3 Testing of the prepared surface 6.3 Thermal spraying 6.3.1 General |
| 76 | 6.3.2 Spray material 6.3.3 Pre-conditions for the execution of thermal spraying process 6.3.4 Execution of thermal spraying 6.3.5 Inspection after spraying |
| 77 | 6.4 Sealing of the coating 6.5 Advice for welding in combination with thermal spraying 6.6 Thermal spraying of corrosion protected fastenings |
| 78 | 7 Tests — Test procedures 7.1 General 7.2 Manufacturing of the accompanying specimens 7.3 Coating thickness 7.3.1 General |
| 79 | 7.3.2 Coatings with a surface below 1 m2 7.3.3 Coatings with surfaces greater than 1 m2 7.3.4 Number of thickness test points 7.3.5 Measurement of the coating thickness |
| 80 | 7.4 Appearance of the coating surface and tests 7.4.1 Visual inspection 7.4.2 Roughness 7.4.3 Adhesion strength 7.4.4 Metallographic examination of the coating 7.5 Defects in the coating and their repair 7.5.1 Defects on the surface and in the coating and their repair |
| 81 | 7.5.2 Reasons for the rejection of a defective sprayed coating 8 Health and safety and environment protection 9 Additional requirements for working on-site 9.1 General 9.2 Supervision of spraying on-site 9.3 Job reference qualification for spray personnel working on-site |
| 82 | 9.4 Execution of spray works in the case of planned work on-site or not planned repairs on new manufactured parts 9.4.1 General 9.4.2 Surface preparation 9.4.3 Masking 9.4.4 Thermal spraying 9.4.5 Spraying of accompanying specimens 9.4.6 Sealing |
| 83 | 10 Execution of spray works on-site in the case of planned maintenance of a service operated coating 10.1 General 10.2 Pre-inspection for assessment of the repair possibility applied by thermal spraying 10.3 Execution of repair-works by thermal spraying 10.3.1 General 10.3.2 Quality control after repair 11 Tests — Test procedures |
| 84 | 12 Documentation of the procedure and tests in the case of maintenance 13 Health and safety and environment protection on-site |
| 85 | Annex A (normative) Adhesion testing using the pull-off test in accordance with ISO 4624 |
| 88 | Annex B (informative) Documentation of the applied maintenance procedure, the thermal spray procedure and test results in the case of a planned maintenance |
| 91 | Annex C (informative) Documentation of the applied thermal spray procedure and test results in the case of a new manufacturing |
| 93 | Annex D (informative) Test certificate for job reference qualification for thermal sprayers working on-site in accordance with ISO 2063‑2 |
| 95 | Annex E (informative) Test specimens — Spray positions |
| 98 | Annex F (informative) Assessment of the coatability |
| 99 | Annex G (informative) Bend test and its execution |
| 101 | Annex H (informative) Additional information for surface preparation |
| 102 | Annex I (informative) Further details for sealing |
| 103 | Annex J (informative) Further instructions for safety and activities on-site |
| 104 | Annex K (informative) Repair procedures of service loaded coatings and recommended repair procedures |
| 105 | Bibliography |
