BS EN ISO 7539-1:2012:2013 Edition
$142.49
Corrosion of metals and alloys. Stress corrosion testing – General guidance on testing procedures
| Published By | Publication Date | Number of Pages |
| BSI | 2013 | 30 |
1.1 This part of ISO 7539 describes the general considerations that apply when designing and conducting tests to assess susceptibility of metals to stress corrosion.
1.2 This part of ISO 7539 also gives some general guidance on the selection of test methods.
NOTE 1 Particular methods of test are not treated in detail in this part of ISO 7539. These are described in the additional parts of ISO 7539.
NOTE 2 This part of ISO 7539 is applicable to cathodic protection conditions.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | Foreword |
| 7 | Section sec_1 Section sec_1.1 Section sec_1.2 Section sec_2 1 Scope 2 Terms and definitions |
| 8 | Section sec_3 Section sec_3.1 Section sec_3.2 Section sec_3.3 Section sec_3.4 3 Background |
| 9 | Section sec_3.5 Section sec_3.6 Section sec_4 Section sec_4.1 Section sec_4.2 Section sec_4.3 Section sec_4.4 Section sec_4.5 4 Selection of test method |
| 10 | Section sec_5 Section sec_5.1 Section sec_5.2 Section sec_5.2.1 Section sec_5.2.2 Section sec_5.2.3 Section sec_5.2.4 Section sec_5.2.5 Section sec_5.2.6 Section sec_5.2.7 5 Stressing systems 5.1 General 5.2 Constant total strain tests |
| 11 | Section sec_5.2.8 Section sec_5.2.9 Section sec_5.3 Section sec_5.3.1 Section sec_5.3.2 Section sec_5.3.3 Section sec_5.3.4 Section sec_5.3.5 5.3 Constant load tests |
| 12 | Section sec_5.3.6 Section sec_5.4 Section sec_5.4.1 Section sec_5.4.2 Section sec_5.4.3 Section sec_5.4.4 5.4 Slow strain rate tests |
| 13 | Section sec_6 Section sec_6.1 Section sec_6.2 Section sec_6.3 Section sec_6.3.1 Section sec_6.3.2 6 Environmental aspects 6.1 General 6.2 Temperature 6.3 Water chemistry |
| 14 | Section sec_6.3.3 Section sec_6.3.4 Section sec_6.3.5 Section sec_6.3.6 |
| 15 | Section sec_6.3.7 Section sec_6.4 Section sec_6.5 Section sec_6.5.1 Section sec_6.5.2 Section sec_6.5.3 Section sec_6.5.4 6.4 Flow rate 6.5 Electrochemical aspects |
| 16 | Section sec_6.5.5 Section sec_6.5.6 Section sec_6.5.7 Section sec_7 Section sec_7.1 Section sec_7.2 Section sec_7.3 7 Time dependent issues 7.1 General 7.2 Pitting and intergranular corrosion 7.3 Hydrogen uptake |
| 17 | Section sec_8 Section sec_8.1 Section sec_8.1.1 Section sec_8.1.2 Section sec_8.1.3 Section sec_8.1.4 Section sec_8.1.5 Section sec_8.2 Section sec_8.2.1 Section sec_8.2.2 8 Specimen design and manufacture 8.1 General 8.2 Surface condition |
| 18 | Section sec_8.2.3 Section sec_8.2.4 Section sec_8.2.5 Section sec_8.2.6 Section sec_8.2.7 Section sec_8.2.8 |
| 19 | Section sec_8.3 Section sec_8.4 Section sec_8.4.1 Section sec_8.4.2 Section sec_8.4.3 Section sec_8.4.4 Section sec_8.4.5 8.3 Area effects 8.4 Pre-cracked test pieces |
| 20 | Section sec_8.5 Section sec_9 Section sec_9.1 Section sec_9.2 Section sec_9.3 8.5 Welds 9 Stress corrosion test cells |
| 21 | Section sec_10 Section sec_11 Section sec_11.1 Section sec_11.2 Section sec_11.4 Section sec_11.5 Section sec_11.6 Section sec_11.7 10 Initiation of stress corrosion tests 11 Assessment and treatment of results |
| 23 | Table tab_a Figure fig_1 |
| 24 | Annex sec_A Annex A (informative) Guide to selection of mechanical test method |
| 25 | Table tab_A.1 |
| 26 | Reference ref_1 Reference ref_2 Reference ref_3 Bibliography |
