BSI PD 6692:2018
$189.07
Asphalt. Guidance on the use of BS EN 12697 “Bituminous mixtures. Test methods”
| Published By | Publication Date | Number of Pages |
| BSI | 2018 | 48 |
This Published Document gives guidance on the use of each of the European test methods for asphalt given in BS EN 12697. The tests are divided into five groups:
-
test methods required for testing the constituent materials, as identified in BS EN 13108‑20:2016, Annex A;
-
test methods called up in at least four of the standard specifications for the different types of asphalt, BS EN 13108‑1 to BS EN 13108‑7, as identified in BS EN 13108‑20:2016, Annex B (see Table 1);
-
test methods called up in only specific standard specifications, as identified in BS EN 13108‑20:2016, Annex B;
-
test procedures used to support the test methods in BS EN 12697‑30 to BS EN 12697‑33, as identified in BS EN 13108‑20:2016, Annex C, plus BS EN 12697‑35; and
-
test methods and procedures not called up in the asphalt standards.
Where standards fit into more than one category, they are described in the first and subsequently cross-referenced. The subclauses describing each of the tests are listed in Table 1.
Table 1 Asphalt tests in BS EN 12697 called up in asphalt specifications BS EN 13108
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 5 | Foreword |
| 7 | 0 Introduction 1 Scope |
| 8 | Table 1 — Asphalt tests in BS EN 12697 called up in asphalt specifications BS EN 13108 |
| 9 | 2 Overview of European Standards defining test methods for asphalts 2.1 “Back of the lorry” 2.2 CE marking |
| 10 | 2.3 Status of tests 2.4 Empirical and fundamental tests |
| 11 | 3 Guidance on test methods required for testing the constituent materials 3.1 BS EN 12697‑1 — Soluble binder content |
| 13 | 3.2 BS EN 12697‑2 — Determination of particle size distribution |
| 14 | 3.3 BS EN 12697‑3 — Bitumen recovery: rotary evaporator 3.4 BS EN 12697‑4 — Bitumen recovery: fractionating column |
| 15 | 3.5 BS EN 12697‑5 — Determination of the maximum density 3.6 BS EN 12697‑6 — Determination of bulk density of bituminous specimens |
| 16 | 3.7 BS EN 12697‑7 — Determination of the bulk density of bituminous specimens by gamma rays |
| 17 | 3.8 BS EN 12697‑8 — Determination of void characteristics of bituminous specimens 3.9 BS EN 12697‑9 — Determination of the reference density 3.10 BS EN 12697‑10 — Compactibility |
| 18 | 3.11 BS EN 12697‑11 — Determination of the affinity between aggregate and bitumen |
| 19 | 3.12 BS EN 12697‑12 — Determination of the water sensitivity of bituminous specimens |
| 20 | 3.13 BS EN 12697‑13 — Temperature measurement 3.14 BS EN 12697‑14 — Water content 3.15 BS EN 12697‑15 — Determination of the segregation sensitivity |
| 21 | 3.16 BS EN 12697‑16 — Abrasion by studded tyres 3.17 BS EN 12697‑17 — Particle loss of porous asphalt specimens |
| 22 | 3.18 BS EN 12697‑18 — Binder drainage |
| 23 | 3.19 BS EN 12697‑19 — Permeability of specimen 3.20 BS EN 12697‑20 — Indentation using cube or cylindrical specimens 3.21 BS EN 12697‑21 — Indentation using plate specimens |
| 24 | 3.22 BS EN 12697‑22 — Wheel tracking |
| 25 | 3.23 BS EN 12697‑23 — Determination of the indirect tensile strength of bituminous specimens 3.24 BS EN 12697‑24 — Resistance to fatigue |
| 27 | 3.25 BS EN 12697‑25 — Cyclic compression test |
| 28 | 3.26 BS EN 12697‑26 — Stiffness |
| 29 | 3.27 BS EN 12697‑27 — Sampling Table 2 — Recommended mass of bulk sample |
| 30 | 3.28 BS EN 12697‑28 — Preparation of samples for determining binder content, water content and grading 3.29 BS EN 12697‑29 — Determination of the dimensions of a bituminous specimen 3.30 BS EN 12697‑30 — Specimen preparation by impact compactor |
| 31 | 3.31 BS EN 12697‑31 — Specimen preparation by gyratory compactor 3.32 BS EN 12697‑32 — Laboratory compaction of bituminous mixtures by vibratory compactor |
| 32 | 3.33 BS EN 12697‑33 — Specimen prepared by roller compactor 3.34 BS EN 12697‑34 — Marshall test |
| 33 | 3.35 BS EN 12697‑35 — Laboratory mixing 3.36 BS EN 12697‑36 — Determination of the thickness of a bituminous pavement |
| 34 | 3.37 BS EN 12697‑37 — Hot sand test for the adhesivity of binder on coated chippings for HRA 3.38 BS EN 12697‑38 — Common equipment and calibration 3.39 BS EN 12697‑39 — Binder content by ignition |
| 35 | 3.40 BS EN 12697‑40 — In situ drainability 3.41 BS EN 12697‑41 — Resistance to de-icing fluids |
| 36 | 3.42 BS EN 12697‑42 — Amount of foreign matter in reclaimed asphault 3.43 BS EN 12697‑43 — Resistance to fuel |
| 37 | 3.44 BS EN 12697‑44 — Crack propagation by semi-circular bending test 3.45 BS EN 12697‑45 — Saturation ageing tensile stiffness (SATS) conditioning test |
| 38 | 3.46 BS EN 12697‑46 — Low temperature cracking and properties by uniaxial tension tests 3.47 BS EN 12697‑47 — Determination of the ash content of natural asphalts |
| 39 | 3.48 prEN 12697‑48 — Interlayer bonding |
| 40 | 3.49 BS EN 12697‑49 — Determination of friction after polishing 3.50 PD CEN/TS 12697‑50 — Resistance to scuffing |
| 41 | 3.51 PD CEN/TS 12697‑51 — Surface shear strength test 3.52 PD CEN/TS 12697‑52 — Conditioning to address oxidative ageing |
| 43 | Bibliography |
Related products
-
BSI PD 6692:2018 – TC:2020 Edition
Tracked Changes. Asphalt. Guidance on the use of BS EN 12697 “Bituminous mixtures. Test methods”…
