ISO 20083-2:2019
$19.50
Ships and marine technology — Determination of the shaft power of ship propulsion systems by measuring the shaft distorsion — Part 2: Optical reflection method
| Published By | Publication Date | Number of Pages |
| ISO | 2019-06 | 18 |
This document specifies a procedure to determine the shaft power of engine ships, by measuring the shaft distortion using an optical reflection type device. It gives the principles of the measurement, the components of the device and the calculation method. It also describes the factors for determining the measuring accuracy, including the calibration procedure, and specifies the on-board documentation for the device.
Related products
-
BS ISO 7267-2:2008 2009
Rubber-covered rollers. Determination of apparent hardness – Shore-type durometer method Published By Publication Date Number…
-
BS ISO/IEC 9798-2:2008 2013
Information technology. Security techniques. Entity authentication – Mechanisms using symmetric encipherment algorithms Published By Publication…
-
BS EN ISO 899-2:2003+A1:2015
Plastics. Determination of creep behaviour – Flexural creep by three-point loading Published By Publication Date…
-
ISO/IEC 24727-2:2008/Amd 1:2014
Identification cards — Integrated circuit card programming interfaces — Part 2: Generic card interface —…
-
BS ISO 2470-2:2008 2009
Paper, board and pulps. Measurement of diffuse blue reflectance factor – Outdoor daylight conditions (D65…
-
BS EN ISO 3382-2:2008 2009
Acoustics. Measurement of room acoustic parameters – Reverberation time in ordinary rooms Published By Publication…
-
BS ISO 26428-2:2008 2009
Digital cinema (D-cinema) distribution master – Audio characteristics Published By Publication Date Number of Pages…
-
BS EN ISO 8230-2:2008 2009
Safety requirements for dry-cleaning machines – Machines using perchloroethylene Published By Publication Date Number of…
-
ISO 21003-2:2008/Amd 1:2011
Multilayer piping systems for hot and cold water installations inside buildings — Part 2: Pipes…
-
ISO/IEC 14443-4:2008/Amd 2:2012
Identification cards — Contactless integrated circuit cards — Proximity cards — Part 4: Transmission protocol…
-
BS EN ISO 20565-2:2008 2010
Chemical analysis of chrome-bearing refractory products and chrome-bearing raw materials (alternative to the X-ray fluorescence…
-
BS ISO 12117-2:2008+A1:2016
Earth-moving machinery. Laboratory tests and performance requirements for protective structures of excavators – Roll-over protective…
-
BS ISO 26622-2:2008 2015
Modular taper interface with ball track system – Dimensions and designation of receivers Published By…
-
BS ISO 26432-2:2008 2009
Digital source processing – Digital cinema (D-cinema) low frequency effects (LFE) channel audio characteristics Published…
-
BS ISO 20283-2:2008 2009
Mechanical vibration. Measurement of vibration on ships – Measurement of structural vibration Published By Publication…
-
UNE-CEN ISO/TS 21083-2:2019
Test method to measure the efficiency of air filtration media against spherical nanomaterials – Part…
-
BS EN ISO 23275-2:2008 2009
Animal and vegetable fats and oils. Cocoa butter equivalents in cocoa butter and plain chocolate…
-
ISO/IEC 21000-3:2003/Amd 2:2013
Information technology — Multimedia framework (MPEG-21) — Part 3: Digital Item Identification — Amendment 2:…
-
ISO 899-2:2003/Amd 1:2015
Plastics — Determination of creep behaviour — Part 2: Flexural creep by three-point loading —…
-
BS EN ISO 734-2:2008 2009
Oilseed meals. Determination of oil content – Rapid extraction method Published By Publication Date Number…
-
BS ISO 3767-2:2008 2015
Tractors, machinery for agriculture and forestry, powered lawn and garden equipment. Symbols for operator controls…
-
BS EN ISO 11348-2:2008+A1:2018:2019 Edition
Water quality. Determination of the inhibitory effect of water samples on the light emission of…
-
ISO/TS 21083-2:2019
Test method to measure the efficiency of air filtration media against spherical nanomaterials — Part…
-
ISO/IEC 23000-9:2008/Amd 2:2010
Information technology — Multimedia application format (MPEG-A) — Part 9: Digital Multimedia Broadcasting application format…
-
BSI 19/30363575 DC:2019 Edition
BS ISO/IEC 12207-2. Systems and software engineering. Software life cycle processes – Part 2. Relation…
-
BS EN ISO 6887-2:2003 2009
Microbiology of food and animal feeding stuffs. Preparation of test samples, initial suspension and decimal…
-
ISO/IEC 7810:2003/Amd 2:2012
Identification cards — Physical characteristics — Amendment 2: Opacity Published By Publication Date Number of…
-
BS ISO 20683-2:2016
Aircraft ground equipment. Design, testing and maintenance requirements for nose gear towbarless towing vehicle (TLTV)…
-
ISO 15152:2003/Amd 2:2018
Tobacco — Determination of the content of total alkaloids as nicotine — Continuous-flow analysis method…
-
BS ISO 7304-2:2008 2009
Alimentary pasta produced from durum wheat semolina. Estimation of cooking quality by sensory analysis –…
-
ISO 15085:2003/Amd 2:2017
Small craft — Man-overboard prevention and recovery — Amendment 2 Published By Publication Date Number…
-
BS EN ISO 21003-2:2008+A1:2011:2024 Edition
Multilayer piping systems for hot and cold water installations inside buildings – Pipes Published By…
-
BS ISO 3290-2:2008 2009
Rolling bearings. Balls – Ceramic balls Published By Publication Date Number of Pages BSI 2009…
-
BS EN ISO 21003-2:2008+A1:2011
Multilayer piping systems for hot and cold water installations inside buildings – Pipes Published By…
-
BS ISO 26430-2:2008 2009
Digital cinema (D-cinema) operations – Digital certificate Published By Publication Date Number of Pages BSI…
-
ISO 20683-2:2016
Aircraft ground equipment — Design, testing and maintenance requirements for nose gear towbarless towing vehicle…
-
BS EN ISO 25539-2:2008 2009
Cardiovascular implants. Endovascular devices – Vascular stents Published By Publication Date Number of Pages BSI…
-
BS ISO/IEC 24727-2:2008+A1:2014
Dentistry. Nomenclature of oral anomalies – Developmental anomalies of teeth Published By Publication Date Number…
-
BS ISO 3937-2:2008 2009
Cutter arbors with tenon drive – Dimensions of 7/24 taper Published By Publication Date Number…
-
ISO/TS 11133-2:2003/Amd 1:2011
Microbiology of food and animal feeding stuffs — Guidelines on preparation and production of culture…
