ISO 3137:1974
$13.00
Anhydrous hydrogen fluoride for industrial use — Sampling
| Published By | Publication Date | Number of Pages |
| ISO | 1974-12 | 8 |
This part contains a method for taking laboratory samples intended for the determination of the water content and the preparations of the test samples. Contains instructions for handling with the material. Applicable for taking samples of this highly corrosive liquid from road and rail tanks, drums and cylinders. The principle consists in allowing the liquid of one of these containers to flow in a cooled evacuated stainless steel cylinder or cylinders of not less than 1 kg total capacity. The apparatus for sampling is shown in a figure. Part Two deals with the preparation of the test sample by introduction of the liquid into a polyolefin cylinder containing two layers of ice. Has also been approved by the IUPAC.
Related products
-
ISO 137:1975
Wool — Determination of fibre diameter — Projection microscope method Published By Publication Date Number…
-
IEEE 9945-2009
IEEE/ISO/IEC International Standard – Information technology Portable Operating System Interface (POSIX(TM)) Base Specifications, Issue 7…
-
ISO 3237:1975
Sodium sulphate for industrial use — Determination of sulphates content — Calculation method and barium…
-
IEC 60695-11-5:2004
Fire hazard testing – Part 11-5: Test flames – Needle-flame test method – Apparatus, confirmatory…
-
BS 4050-1:1977
Specification for mosaic parquet panels – General characteristics Published By Publication Date Number of Pages…
-
BS EN 578:1994
Plastics piping systems. Plastics pipes and fittings. Determination of the opacity Published By Publication Date…
-
ISA S72.02-1994
Manufacturing Message Specification: Companion Standard for Process Control Published By Publication Date Number of Pages…
-
ISO 3139:1976/Amd 1:1980
Aqueous hydrofluoric acid for industrial use — Sampling and methods of test — Amendment 1…
-
BS 1142:1989
Specification for fibre building boards Published By Publication Date Number of Pages BSI 1989 46
-
BS 3G 100-2.3.15:1978
Specification for general requirements for equipment for use in aircraft. All equipment. Environmental conditions –…
-
ISO 3437:1975
Road vehicles — Determination of fuel leakage in the event of a collision Published By…
-
ISO 3317:2009
Assembly tools for screws and nuts — Square drive adaptor with hexagon or cylindrical flat…
-
AS/NZS 1080.3:2000 (R2016)
Timber – Methods of test – Density Published By Publication Date Number of Pages AS…
-
BS 5365-1:1976
Methods of sampling and test for anhydrous hydrogen fluoride for industrial use – Sampling Published…
-
HPS N43.4-2005
Classification of Radioactive Self-Luminous Light Sources Published By Publication Date Number of Pages HPS 2005…
-
ISO 3139:1976
Acide fluorhydrique en solution à usage industriel — Échantillonnage et méthodes d’essai Published By Publication…
-
ISO 3132:1975
Wood — Testing in compression perpendicular to grain Published By Publication Date Number of Pages…
-
ISO 3131:1975
Wood — Determination of density for physical and mechanical tests Published By Publication Date Number…
-
ISO 317:1984
Manganese ores and concentrates — Determination of arsenic content — Spectrometric method Published By Publication…
-
ISO 3147:1975
Heat exchangers — Verification of thermal balance of water-fed or steam-fed primary circuits — Principles…
-
ISO 3173:1974
Road vehicles — Apparatus for measurement of the opacity of exhaust gas from diesel engines…
-
BS EN 60695-11-5:2005
Fire hazard testing – Test flames – Needle-flame test method. Apparatus, confirmatory test arrangement and…
-
BS 3397:1976
Methods of test for synthetic rubber latices Published By Publication Date Number of Pages BSI…
-
ISO 3197:1975
Sodium hydroxide for industrial use — Determination of chlorides content — Photometric method Published By…
-
IEEE/ISO/IEC 9945 2009
IEEE/ISO/IEC International Standard – Information technology Portable Operating System Interface (POSIX(TM)) Base Specifications, Issue 7…
-
ISO 3737:1976
Agricultural tractors and self-propelled machines — Test method for enclosure pressurization systems Published By Publication…
-
ISO 3130:1975
Wood — Determination of moisture content for physical and mechanical tests Published By Publication Date…
-
BS 5182:1975
Method for the measurement of the length of wool fibres processed on the worsted system,…
-
BS 2481-3:1982
Typewriters – Specification for layout of printing and function keys Published By Publication Date Number…
-
ISO 3177:1975
Potassium hydroxide for industrial use — Determination of chlorides content — Photometric method Published By…
-
ISO 3127:1994
Thermoplastics pipes — Determination of resistance to external blows — Round-the-clock method Published By Publication…
-
BS 4401-11:1979
Methods of test for meat and meat products – Determination of L(-)-hydroxyproline content (reference method)…
-
ISO 3138:1974
Anhydrous hydrogen fluoride for industrial use — Determination of non-volatile acid content — Titrimetric method…
-
BS 5365-2:1976
Methods of sampling and test for anhydrous hydrogen fluoride for industrial use – Determination of…
-
BS 4991:1974
Specification for propylene copolymer pressure pipe Published By Publication Date Number of Pages BSI 1974…
-
BS 5050:1974
Methods of test for cryolite Published By Publication Date Number of Pages BSI 1974 20
-
ISO/TR 4137:1978
Plastics — Determination of modulus of elasticity by alternating flexure Published By Publication Date Number…
-
ISO 3117:1977
Tangential keys and keyways Published By Publication Date Number of Pages ISO 1977-04 6
-
ISO 3133:1975
Wood — Determination of ultimate strength in static bending Published By Publication Date Number of…
-
BS 373:1957
Methods of testing small clear specimens of timber Published By Publication Date Number of Pages…
