ISO 48-5:2018
$13.00
Rubber, vulcanized or thermoplastic — Determination of hardness — Part 5: Indentation hardness by IRHD pocket meter method
| Published By | Publication Date | Number of Pages |
| ISO | 2018-08 | 12 |
This document specifies a method for determining the indentation hardness of vulcanized or thermoplastic rubber by means of a pocket hardness meter calibrated in IRHD. The use of such meters is primarily intended for control, not specification, purposes (for specification, see ISO 48-2). It is possible to increase precision by fixing the pocket hardness meter on a support.
Related products
-
BS ISO 48:2010
Rubber, vulcanized or thermoplastic. Determination of hardness (hardness between 10 IRHD and 100 IRHD) Published…
-
BSI PD CEN/TR 17868:2022
Intelligent transport systems. EU-ICIP. ITS standards deliverables (2022) Published By Publication Date Number of Pages…
-
ISO 19453-4:2018
Road vehicles — Environmental conditions and testing for electrical and electronic equipment for drive system…
-
BS ISO 48-6:2018
Rubber, vulcanized or thermoplastic. Determination of hardness – Apparent hardness of rubber-covered rollers by IRHD…
-
BS ISO 29281-1:2018
Intelligent transport systems. Localized communications – Fast networking & transport layer protocol (FNTP) Published By…
-
ISO/TR 21954:2018
Guidance on the selection of the appropriate means of ventilation based on the intended patient,…
-
ISO/TS 19293:2018
Health informatics — Requirements for a record of a dispense of a medicinal product Published…
-
ISO/IEC TR 20000-5:2013
Information technology — Service management — Part 5: Exemplar implementation plan for ISO/IEC 20000-1 Published…
-
BS ISO 48-4:2018
Rubber, vulcanized or thermoplastic. Determination of hardness – Indentation hardness by durometer method (Shore hardness)…
-
ISO 8178-5:2015
Reciprocating internal combustion engines — Exhaust emission measurement — Part 5: Test fuels Published By…
-
BS ISO 48-3:2018
Rubber, vulcanized or thermoplastic. Determination of hardness – Dead-load hardness using the very low rubber…
-
BS ISO 48-3:2018 – TC:2020 Edition
Tracked Changes. Rubber, vulcanized or thermoplastic. Determination of hardness – Dead-load hardness using the very…
-
BS ISO 7619-2:2010
Rubber, vulcanized or thermoplastic. Determination of indentation hardness – IRHD pocket meter method Published By…
-
BS ISO 48-8:2018
Rubber, vulcanized or thermoplastic. Determination of hardness – Apparent hardness of rubber-covered rollers by Pusey…
-
IEEE 24748-5-2017
ISO/IEC/IEEE International Standard – Systems and Software Engineering–Life Cycle Management–Part 5: Software Development Planning Published…
-
BS EN ISO 4885:2018
Ferrous materials. Heat treatments. Vocabulary Published By Publication Date Number of Pages BSI 2018 48
-
BS ISO 48-8:2018 – TC:2020 Edition
Tracked Changes. Rubber, vulcanized or thermoplastic. Determination of hardness – Apparent hardness of rubber-covered rollers…
-
BS ISO 48-2:2018
Rubber, vulcanized or thermoplastic. Determination of hardness – Hardness between 10 IRHD and 100 IRHD…
-
BS ISO 48-9:2018
Rubber, vulcanized or thermoplastic. Determination of hardness – Calibration and verification of hardness testers Published…
-
BS ISO 48-1:2018
Rubber, vulcanized or thermoplastic. Determination of hardness – Introduction and guidance Published By Publication Date…
-
ISO/IEC/IEEE 24748-5:2017
Systems and software engineering — Life cycle management — Part 5: Software development planning Published…
-
ISO/TR 7637-5:2016
Road vehicles — Electrical disturbances from conduction and coupling — Part 5: Enhanced definitions and…
-
BSI 19/30381225 DC:2019 Edition
BS ISO 81001-1. Health software and health IT systems safety, effectiveness and security. Foundational principles,…
-
BS ISO 48-6:2018 – TC:2020 Edition
Tracked Changes. Rubber, vulcanized or thermoplastic. Determination of hardness – Apparent hardness of rubber-covered rollers…
-
ISO/IEC 14543-5-11:2018
Information technology — Home electronic systems (HES) architecture — Part 5-11: Intelligent Grouping and Resource…
-
BS ISO 48-5:2018
Rubber, vulcanized or thermoplastic. Determination of hardness – Indentation hardness by IRHD pocket meter method…
-
BS EN IEC 60601-2-16:2019
Medical electrical equipment – Particular requirements for the basic safety and essential performance of haemodialysis,…
-
ISO/IEC TS 22237-7:2018
Information technology — Data centre facilities and infrastructures — Part 7: Management and operational information…
-
BSI PD ISO/IEC TR 20000-7:2019
Information technology. Service management – Guidance on the integration and correlation of ISO/IEC 20000-1:2018 to…
-
BS ISO 48-7:2018
Rubber, vulcanized or thermoplastic. Determination of hardness – Apparent hardness of rubber-covered rollers by Shore-type…
-
IEEE ISO IEC 24748 5 2017
ISO/IEC/IEEE International Standard – Systems and Software Engineering–Life Cycle Management–Part 5: Software Development Planning Published…
-
BSI 14/30292519 DC:2014 Edition
BS EN ISO 80369-5. Small-bore connectors for liquids and gases in healthcare applications. Connectors for…
-
BS ISO/IEC 11770-3:2015+A1:2017:2018 Edition
Information technology. Security techniques. Key management – Part 3: Mechanisms using asymmetric techniques Published By…
-
BS ISO 48-7:2018 – TC:2020 Edition
Tracked Changes. Rubber, vulcanized or thermoplastic. Determination of hardness – Apparent hardness of rubber-covered rollers…
-
BSI PD CEN/TR 14067-7:2021
Railway applications. Aerodynamics – Fundamentals for test procedures for train-induced ballast projection Published By Publication…
-
BS ISO 24102-4:2018
Intelligent transport systems. ITS station management – Station-internal management communications Published By Publication Date Number…
-
BSI PD ISO/IEC TR 20000-7:2019
Information technology. Service management – Guidance on the integration and correlation of ISO/IEC 20000-1:2018 to…
-
BS ISO 48-5:2018 – TC:2020 Edition
Tracked Changes. Rubber, vulcanized or thermoplastic. Determination of hardness – Indentation hardness by IRHD pocket…
-
BSI 19/30330682 DC:2019 Edition
BS EN ISO 15883-5. Washer disinfectors – Part 5. Performance requirements and test method criteria…
-
ISO/TR 19591:2018
Personal protective equipment for firefighters — Standard terms and definitions Published By Publication Date Number…
