ISO 7363:1986
$19.50
Grues et appareils de levage — Caractéristiques techniques et documents d’acceptation
| Published By | Publication Date | Number of Pages |
| ISO | 1986-03 | 16 |
Establishes the form of presentation and content of the documents which a manufacturer should provide with the equipment. Documents give technical information and include acceptance documents for the equipment to facilitate its installation, testing and use. Specimen acceptance documents are given in the annex. Applies to all types defined in ISO 4306-1.
Related products
-
BS 5773-8:1983
Metric needle roller bearings – Specification for tolerances of track rollers Published By Publication Date…
-
BS 5363:1976
Method for measurement of reverberation time in auditoria Published By Publication Date Number of Pages…
-
BS 7163:1990
Specification for wire rope and pulley steering systems on small craft Published By Publication Date…
-
ISO 7353:1985
Oil of rosewood — Determination of alpha-terpineol content — Gas chromatographic method on packed columns…
-
BS 3680-10B:1980
Measurement of liquid flow in open channels. Sediment transport – Measurement of suspended sediment Published…
-
BS 3182-1:1978
Textile machinery and accessories: healds, heald frames and reeds. – Specification for flat steel healds…
-
ISO 7373:1987
Ferroalloys — Experimental methods for checking the precision of sample division Published By Publication Date…
-
BS 3680-3G:1990
Measurement of liquid flow in open channels. Stream flow measurement – General guidelines for the…
-
ISO 7393-1:1985
Water quality — Determination of free chlorine and total chlorine — Part 1: Titrimetric method…
-
BS EN 27963:1992
Specification for calibration block No. 2 for ultrasonic examination of welds Published By Publication Date…
-
ISO 7336:1984
Asbestos-cement pipelines — Guidelines for hydraulic calculation Published By Publication Date Number of Pages ISO…
-
ISO 7657:1995
Pipework — General requirements for stripwound flexible metal hoses Published By Publication Date Number of…
-
ISO 7313:1984
Aircraft — High temperature convoluted hose assemblies in polytetrafluoroethylene (PTFE) Published By Publication Date Number…
-
BS 5555:1981:1983 Edition
Specification for SI units and recommendations for the use of their multiples and of certain…
-
BS 684-2.42:1989
Methods of analysis of fats and fatty oils. Other methods – Determination of 1-monoglycerides and…
-
ISO 7361:1986
Performance standards in building — Presentation of performance levels of facades made of same-source components…
-
BS 6844:1987
Method for determination of the flat crush resistance of corrugating medium after laboratory fluting (CMT…
-
BS 6845:1996
Method for evaluation of vulcanization characteristics of halogenated isobutene-isoprene rubber (BIIR and CIIR) Published By…
-
ISO 7368:1989
Hydraulic fluid power — Two-port slip-in cartridge valves — Cavities Published By Publication Date Number…
-
BS 733-1:1983
Pyknometers – Specification Published By Publication Date Number of Pages BSI 1983 14
-
BS EN ISO 7393-1:2000
Water quality. Determination of free chlorine and total chlorine – Titrimetric method using N,N-diethyl-1,4-phenylenediamine Published…
-
BS 5773-7:1980
Metric needle roller bearings – Specification for dimensions of track rollers Published By Publication Date…
-
JIS H 4080:2006
Aluminum and Aluminum Alloys Extruded Tubes and Cold-Drawn Tubes Published By Publication Date Number of…
-
BS 5255:1989
Specification for thermoplastics waste pipe and fittings Published By Publication Date Number of Pages BSI…
-
BS 5710:1979
Methods for macroscopic assessment of the content of non-metallic inclusions in wrought steels Published By…
-
BS 6501-2:1988
Flexible metallic hose assemblies – Specification for strip wound hoses and hose assemblies Published By…
-
ISO 8449:1995
Pipework — Single overlap flexible metal hoses (with packing, limited tightness, circular or polygonal section,…
-
ISO 7633:1985
Road vehicles — Elastomeric boots for drum type hydraulic brake wheel cylinders using a petroleum…
-
BS ISO 7663:2005 2006
Halogenated isobutene-isoprene rubber (BIIR and CIIR). Evaluation procedures Published By Publication Date Number of Pages…
-
BS EN ISO 7263:1995
Corrugating medium. Determination of the flat crush resistance after laboratory fluting Published By Publication Date…
-
JIS G 0556:2014
Method of macro-streak-flaw test for steel Published By Publication Date Number of Pages JIS 2014-03-20…
-
ISO 7863:1984
Micromètres verticaux et rehausses Published By Publication Date Number of Pages ISO 1984-05 8
-
BS ISO 7063:2003 2004
Rolling bearings. Needle roller bearing track rollers. Boundary dimensions and tolerances Published By Publication Date…
-
ISO 7364:1983
Shipbuilding and marine structures — Deck machinery — Accommodation ladder winches Published By Publication Date…
-
ISO 3363:1976
Hydrocarbures fluoro-chlorés à usage industriel — Détermination de l’acidité — Méthode titrimétrique Published By Publication…
-
ISO 3763:1976
Wrought steels — Macroscopic methods for assessing the content of non-metallic inclusions Published By Publication…
-
ISO 7366:1987
Animal and vegetable fats and oils — Determination of 1-monoglycerides and free glycerol contents Published…
-
BS 6845:1987
Method for evaluation of vulcanization characteristics of halogenated isobutene-isoprene rubber (BIIR and CIIR) Published By…
-
BS EN ISO 7393-2:2000
Water quality. Determination of free chlorine and total chlorine – Colorimetric method using N,N-diethyl-1,4-phenylenediamine for…
-
ISO 7393-2:1985
Water quality — Determination of free chlorine and total chlorine — Part 2: Colorimetric method…
