77.140.25 – Spring steels – PDF Standards Store ?u= Wed, 06 Nov 2024 02:22:08 +0000 en-US hourly 1 https://wordpress.org/?v=6.7.1 ?u=/wp-content/uploads/2024/11/cropped-icon-150x150.png 77.140.25 – Spring steels – PDF Standards Store ?u= 32 32 JIS G 4802:2019 ?u=/product/publishers/jis/jis-g-48022019/ Wed, 06 Nov 2024 02:22:08 +0000 Cold-reduced steel strip for springs
Published By Publication Date Number of Pages
JIS 2019-09-20 19
]]> This Standard specifies requirements for steel strips (hereafter referred to as strips) and steel sheets cut from strips (hereafter referred to as cut lengths), that are mainly used for the manufacture of flat springs and coiled springs.

NOTE The International Standard corresponding to this Standard and the symbol of degree of correspondence are as follows.

ISO 4960:2007 Cold-reduced carbon steel strip with a mass fraction of carbon over 0.25 % (MOD)

In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/IEC Guide 21-1.

]]> JIS G 4802:2011 ?u=/product/publishers/jis/jis-g-48022011/ Wed, 06 Nov 2024 02:22:08 +0000 Cold-rolled steel strip for springs
Published By Publication Date Number of Pages
JIS 2011-02-21 17
]]> This Standard specifies the steel strips mainly used for the flat springs and coiled springs (hereafter referred to as "strips").

Also, this Standard applies to the cut-lengths that are cut from the strips.

NOTE: The International Standard corresponding to this Standard and the symbol of degree of correspondence are as follows:

ISO 4960: 2007 Cold-reduced carbon steel strip with a mass fraction of carbon over 0.25 % (MOD)

The symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/lEC Guide 21-1.

]]> JIS G 4802:2005 ?u=/product/publishers/jis/jis-g-48022005/ Wed, 06 Nov 2024 02:22:07 +0000 Cold-Rolled Steel Strips for Springs
Published By Publication Date Number of Pages
JIS 2005-03-20 18
]]> Cold-Rolled Steel Strips for Springs
Published By Publication Date Number of Pages
JIS 2005-03-20 18
]]> JIS G 4801:2021 ?u=/product/publishers/jis/jis-g-48012021/ Wed, 06 Nov 2024 02:22:06 +0000 Spring steels
Published By Publication Date Number of Pages
JIS 2021-02-22 19
]]> This Standard specifies the requirements for the spring steels (hereafter referred to as steels) mainly used for the hot formed springs such as laminated springs, coiled springs and torsion bar springs. The steels include round bars, wire rods, wires, flat bars, sheets and strips.

NOTE The International Standard corresponding to this Standard and the symbol of degree of correspondence are as follows.

ISO 683-14 : 2004 Heat-treatable steels, alloy steels and free-cutting steels — Part 14 : Hot-rolled steels for quenched and tempered springs (MOD)

In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/IEC Guide 21-1.

]]> JIS G 4801:2011 ?u=/product/publishers/jis/jis-g-48012011/ Wed, 06 Nov 2024 02:22:05 +0000 Spring steels
Published By Publication Date Number of Pages
JIS 2011-02-21 19
]]> This Standard specifies the spring steels (hereafter referred to as "steels") mainly used for the hot-formed springs such as the laminated springs, coiled springs and torsion bar springs.

NOTE: The International Standard corresponding to this Standard and the symbol of degree of correspondence are as follows:

ISO 683-14:2004 Heat-treatable steels, alloy steels and free-cutting steels—Part 14: Hot-rolled steels for quenched and tempered springs (MOD)

The symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/IEC Guide 21-1.

]]> JIS G 4801:2005 ?u=/product/publishers/jis/jis-g-48012005/ Wed, 06 Nov 2024 02:22:05 +0000 Spring Steels
Published By Publication Date Number of Pages
JIS 2005-08-20 18
]]> Spring Steels
Published By Publication Date Number of Pages
JIS 2005-08-20 18
]]> JIS G 4314:2013 ?u=/product/publishers/jis/jis-g-43142013/ Wed, 06 Nov 2024 02:21:52 +0000 Stainless steel wires for springs
Published By Publication Date Number of Pages
JIS 2013-02-20 18
]]> This Standard specifies the stainless steel wires for springs (hereafter referred to as "wires") produced by using stainless steel wire rods.

NOTE: The International Standard corresponding to this Standard and the symbol of degree of correspondence are as follows.

ISO 6931-1: 1994 Stainless steels for springs-Part 1: Wire (MOD)

The symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/ lEC Guide 21-1.

]]> JIS G 4314:1994 ?u=/product/publishers/jis/jis-g-43141994/ Wed, 06 Nov 2024 02:21:50 +0000 Stainless Steel Wires for Springs
Published By Publication Date Number of Pages
JIS 1994-11-01 10
]]> Stainless Steel Wires for Springs
Published By Publication Date Number of Pages
JIS 1994-11-01 10
]]> JIS G 4313:1996 ?u=/product/publishers/jis/jis-g-43131996/ Wed, 06 Nov 2024 02:21:49 +0000 Cold Rolled Stainless Steel Strip for Springs
Published By Publication Date Number of Pages
JIS 1996-06-01 14
]]> Cold Rolled Stainless Steel Strip for Springs
Published By Publication Date Number of Pages
JIS 1996-06-01 14
]]> JIS G 4313:2011 ?u=/product/publishers/jis/jis-g-43132011/ Wed, 06 Nov 2024 02:21:49 +0000 Cold rolled stainless steel strip for springs
Published By Publication Date Number of Pages
JIS 2011-02-21 21
]]> This Standard specifies the stainless steel strip mainly used for flat springs and spiral (hereafter referred to as "the strip").

Further, this Standard applies to the cut-to-length which is cut from the strip.

NOTE: The International Standard corresponding to this Standard and the symbol of degree of correspondence are as follows :

ISO 6931-2 : 2005 Stainless steels for springs – Part 2 : Narrow strip (MOD)

The symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/IEC Guide 21-1.

]]>