{"id":115212,"date":"2024-10-19T03:07:12","date_gmt":"2024-10-19T03:07:12","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/astm-a635-a635m-2013\/"},"modified":"2024-10-24T22:18:11","modified_gmt":"2024-10-24T22:18:11","slug":"astm-a635-a635m-2013","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/astm\/astm-a635-a635m-2013\/","title":{"rendered":"ASTM-A635\/A635M 2013"},"content":{"rendered":"

ASTM A635\/A635M-13<\/h3>\n

Historical Standard: Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General Requirements for<\/h4>\n
\n

ASTM A635\/A635M<\/h4>\n

Scope<\/strong><\/p>\n

\n

1.1 This specification covers the general requirements for hot-rolled, heavy-thickness sheet and strip in coils.<\/p>\n<\/p><\/div>\n

\n

1.2 It applies to Specifications A414\/A414M, A424\/A424M, and A1018\/A1018M.<\/p>\n<\/p><\/div>\n

\n

1.3 This material is available only in coils described as follows:<\/p>\n

\n
\n A<\/i><\/sup> Hot-rolled heavy thickness sheet in coils less than 12 in. [300 mm] and less in width must have slit edges. Hot-rolled heavy thickness coils 12 in. [300 mm] and wider with mill edge is considered hot-rolled heavy thickness strip.\n <\/div>\n
\n Note 1<\/span>\u2014The changes in width limits with the publication of A635\/A635M\u2009\u2013\u200906a result in a change in tensile testing direction for material from 0.180 in. [4.5 mm] to 0.230 in. exclusive [6.0 mm exclusive] over 48 in. [1200 mm] wide as that material is now covered by Specification A568\/A568M\u2009\u2013\u200906a. The purchaser is advised to discuss this change with the supplier.<\/span>\n <\/div>\n<\/p><\/div>\n<\/p><\/div>\n
\n

1.4 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification.<\/p>\n<\/p><\/div>\n

\n

1.5 Annex A1<\/span> lists permissible variations in dimensions and mass (see Note 2) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1<\/span> is mandatory when the \u201cM\u201d specification is used.<\/p>\n

\n Note 2<\/span>\u2014The term weight<\/span> is used when inch-pound units are the standard. However, under SI, the preferred term is mass<\/span>.<\/span>\n <\/div>\n<\/p><\/div>\n
\n

1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.<\/p>\n<\/p><\/div>\n

\n

1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable \u201cM\u201d specification designation (SI units), the material shall be furnished to inch-pound units.<\/p>\n<\/p><\/div>\n

Keywords<\/strong><\/p>\n

carbon ; commercial; drawing; heavy thickness coils; high-strength low-alloy; high-strength low-alloy with improved formability; sheet steel; strip steel<\/p>\n

ICS Code<\/strong><\/p>\n

ICS Number Code 77.140.50 (Flat steel products and semi-products)<\/p>\n

DOI:<\/strong> 10.1520\/A0635_A0635M-13<\/p>\n<\/div>\n","protected":false},"excerpt":{"rendered":"

A635\/A635M-13 Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General Requirements for<\/b><\/p>\n\n\n\n\n
Published By<\/td>\nPublication Date<\/td>\nNumber of Pages<\/td>\n<\/tr>\n
ASTM<\/b><\/a><\/td>\n2013<\/td>\n11<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":115213,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[1118,2637],"product_tag":[],"class_list":{"0":"post-115212","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-77-140-50","7":"product_cat-astm","9":"first","10":"instock","11":"sold-individually","12":"shipping-taxable","13":"purchasable","14":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/115212","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/115213"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=115212"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=115212"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=115212"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}