This document specifies acceptance and periodic reverification tests of CMM performance with contacting probing systems and is only applicable to CMMs using:<\/p>\n
any type of contacting probing system; and<\/p>\n<\/li>\n
spherical or hemispherical stylus tip(s).<\/p>\n<\/li>\n<\/ul>\n
CMM probing performance tests are specified by the maximum permissible errors (MPEs), due to the impracticality of isolating the performance of the probing system from that of the CMM, even on a small artefact such as a test sphere.<\/p>\n<\/div>\n
This document applies to CMMs supplied with any of the following:<\/p>\n
single-stylus probing systems;<\/p>\n<\/li>\n
multi-stylus probing systems with fixed multiple styli attached to a single probe (e.g. \u201cstar\u201d stylus);<\/p>\n<\/li>\n
multiple probing systems such as those with a stylus for each of their probes;<\/p>\n<\/li>\n
systems with articulating probing systems;<\/p>\n<\/li>\n
stylus and probe changing systems;<\/p>\n<\/li>\n
manual (non-driven) and automated CMMs;<\/p>\n<\/li>\n
installations including a scanning probe, capable of being used in a scanning mode.<\/p>\n<\/li>\n<\/ol>\n
This document is not applicable to non-contacting probing systems, which require different testing procedures.<\/p>\n
The term \u2018combined CMM and multi-stylus probing system size error\u2019 has been shortened to \u2018multi-stylus size error\u2019 for convenience. This applies in similar cases.<\/p>\n
If it is desirable to isolate the probing system performance as far as is practical, the influence of the CMM can be minimized but not eliminated. See Annex C<\/span> for more information.<\/p>\n Geometrical product specifications (GPS). Acceptance and reverification tests for coordinate measuring systems (CMS) – Coordinate measuring machines (CMMs) using single and multiple stylus contacting probing systems using discrete point and\/or scanning measuring mode<\/b><\/p>\nPDF Catalog<\/h4>\n
\n
\n PDF Pages<\/th>\n PDF Title<\/th>\n<\/tr>\n \n 2<\/td>\n National foreword <\/td>\n<\/tr>\n \n 4<\/td>\n European foreword <\/td>\n<\/tr>\n \n 7<\/td>\n Foreword <\/td>\n<\/tr>\n \n 8<\/td>\n Introduction <\/td>\n<\/tr>\n \n 11<\/td>\n 1 Scope
2 Normative references <\/td>\n<\/tr>\n\n 12<\/td>\n 3 Terms and definitions <\/td>\n<\/tr>\n \n 18<\/td>\n 4 Symbols <\/td>\n<\/tr>\n \n 20<\/td>\n 5 Rated operating conditions
5.1 Environmental conditions <\/td>\n<\/tr>\n\n 21<\/td>\n 5.2 Operating conditions
6 Acceptance tests and reverification tests
6.1 General <\/td>\n<\/tr>\n\n 22<\/td>\n 6.2 Measuring equipment
6.2.1 Test sphere <\/td>\n<\/tr>\n\n 23<\/td>\n 6.2.2 Styli specification and information <\/td>\n<\/tr>\n \n 24<\/td>\n 6.3 Single-stylus probing test
6.3.1 Application
6.3.2 Principle
6.3.3 Procedure <\/td>\n<\/tr>\n\n 26<\/td>\n 6.3.4 Data analysis
6.4 Scanning mode test
6.4.1 Principle
6.4.2 Procedure <\/td>\n<\/tr>\n\n 28<\/td>\n 6.4.3 Data analysis <\/td>\n<\/tr>\n \n 29<\/td>\n 6.5 Multi-stylus test: Fixed multi-probe and multi-stylus probing systems
6.5.1 Principle
6.5.2 Procedure <\/td>\n<\/tr>\n\n 32<\/td>\n 6.5.3 Data analysis
6.6 Multi-stylus test: Articulating probing systems
6.6.1 Principle <\/td>\n<\/tr>\n\n 33<\/td>\n 6.6.2 Procedure <\/td>\n<\/tr>\n \n 35<\/td>\n 6.6.3 Data analysis
6.7 Data analysis for multi-stylus tests
6.7.1 Location error
6.7.2 Opposing-styli projected location error
6.7.3 Multi-stylus size and form error <\/td>\n<\/tr>\n\n 36<\/td>\n 7 Conformance with specification: Acceptance and reverification tests <\/td>\n<\/tr>\n \n 37<\/td>\n 8 Applications
8.1 Acceptance tests
8.2 Reverification tests
8.3 Interim checks <\/td>\n<\/tr>\n\n 38<\/td>\n Annex A (informative) Ring gauge tests <\/td>\n<\/tr>\n \n 42<\/td>\n Annex B (informative) Checking the probing system prior to the ISO 10360-2 test <\/td>\n<\/tr>\n \n 43<\/td>\n Annex C (informative) Interpretation of multi-stylus test results <\/td>\n<\/tr>\n \n 45<\/td>\n Annex D (normative) Maximum permissible error\/limit specification methods <\/td>\n<\/tr>\n \n 47<\/td>\n Annex E (informative) Workpiece related influences <\/td>\n<\/tr>\n \n 49<\/td>\n Annex F (normative) Acceptance tests and reverification tests using small sphere test equipment <\/td>\n<\/tr>\n \n 50<\/td>\n Annex G (informative) Relation to the GPS matrix model <\/td>\n<\/tr>\n \n 52<\/td>\n Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" \n\n
\n Published By<\/td>\n Publication Date<\/td>\n Number of Pages<\/td>\n<\/tr>\n \n BSI<\/b><\/a><\/td>\n 2020<\/td>\n 54<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":359649,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[256,2641],"product_tag":[],"class_list":{"0":"post-359639","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-17-040-30","7":"product_cat-bsi","9":"first","10":"instock","11":"sold-individually","12":"shipping-taxable","13":"purchasable","14":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/359639","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/359649"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=359639"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=359639"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=359639"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}