New IEEE Standard – Inactive – Superseded. Superseded by 1210-2004 Criteria and test methods for determining the compatibility of cable-pulling lubricants (compounds) with cable jacket or other exterior cable covering are described in this standard. Cable-pulling lubricants are used to lower the tension on cable as it is pulled into conduit, duct, or directionally bored holes. Compatibility is important because lubricants should not negatively interact with the cables they lubricate. Compatiblity of lubricants with a variety of common cable coverings is considered.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 1<\/td>\n | Title Page <\/td>\n<\/tr>\n | ||||||
| 3<\/td>\n | Introduction Participants <\/td>\n<\/tr>\n | ||||||
| 6<\/td>\n | CONTENTS <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | 1. Overview 1.1 Scope 1.2 Purpose <\/td>\n<\/tr>\n | ||||||
| 8<\/td>\n | 2. References 3. Physical property effects 3.1 General 3.2 Lubricant on polyvinyl chloride (PVC) jacket <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | 3.3 Lubricant on black polyethylene (PE) jacket 3.4 Lubricant on thermoplastic chlorinated polyethylene (CPE) jacket 3.5 Lubricant on natural rubber jacket <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | 3.6 Lubricant on styrene butadiene rubber (SBR) jacket 3.7 Lubricant on thermoset polychloroprene jacket 3.8 Lubricant on acrylonitrile\/butadiene and polyvinyl chloride (PVC) jacket <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | 3.9 Lubricant on a thermoset chlorosulfonated polyethylene (CSPE) jacket 3.10 Lubricant on thermoset chlorinated polyethylene (CPE) jacket <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 4. Electrical property effects 4.1 General 4.2 Lubricant on semiconducting jackets or exposed semiconducting shields 4.3 Determining stability of lubricant on semiconducting materials (IEEE Std 1026- 1995 [B13]) <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 4.4 Final high-temperature volume resistivity test (AEIC CS5-94 [B1], AEIC CS6-96 [B2], AEIC CS7-… 4.5 Lubricant on exposed thermoplastic primary insulation <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | 4.6 Lubricant on exposed thermoset primary insulation <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | 5. Testing and test methods 5.1 General 5.2 Jacket test specimens for the immersion\/physical property tests 5.3 Tensile strength and elongation test <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | 5.4 Heated lubricant immersion method 5.5 Heated water\/air immersion method 5.6 Environmental stress cracking test <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | 5.7 Specimens for volume resistivity tests (stability and final high temperature) 5.8 Specimens and test for semiconducting jacket and self-supporting lubricants 5.9 Specimens and tests for semiconducting insulation shield with self-supporting lubricants <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | 5.10 Volume resistivity test procedure for self-supporting lubricants on semicon ducting jackets\/… <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | 5.11 Specimens and tests for semiconducting jackets\/shields when lubricants are not self-supporti… 5.12 Preparation of samples for the dielectric voltage withstand test in water 5.13 Dielectric voltage withstand test in water <\/td>\n<\/tr>\n | ||||||
| 20<\/td>\n | Annex A\u2014Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" IEEE Standard Tests for Determining Compatibility of Cable-Pulling Lubricants With Wire and Cable<\/b><\/p>\n |