ASME Y14.41 2012

$98.04

ASME Y14.41 Digital Product Definition Data Practices

Published By	Publication Date	Number of Pages
ASME	2012	116

Guaranteed Safe Checkout

Category: ASME

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

This Standard establishes requirements and reference documents applicable to the preparation and revision of digital product definition data, hereafter referred to as data sets. This Standard defines exceptions and additional requirements to existing ASME standards for using product definition digital data sets or drawings in digital format. Where no exception or additional requirements are stated, existing ASME standards shall apply.

PDF Catalog

PDF Pages	PDF Title
5	CONTENTS
7	FOREWORD
8	ASME Y14 COMMITTEE Engineering Drawing and Related Documentation Practices
9	CORRESPONDENCE WITH THE Y14 COMMITTEE
11	DIGITAL PRODUCT DEFINITION DATA PRACTICES Section 1 General 1.1 SCOPE 1.2 STRUCTURE OF STANDARD 1.3 ASME Y14 SERIES CONVENTIONS 1.3.1 Mandatory, Nonmandatory, Guidance, and Optional Words 1.3.2 Cross-Reference of Standards. 1.3.3 Invocation of Referenced Standards. 1.3.4 Parentheses Following a Definition. 1.3.5 Notes.
12	1.3.6 Acronyms and Abbreviations. 1.3.7 Units. 1.3.8 Figures. 1.3.9 Precedence of Standards. 1.3.10 Unless Otherwise Specified UOS. 1.4 REFERENCE TO THIS STANDARD 1.5 SYMBOLS
13	Section 2 References
14	Section 3 Terms and Definitions 3.1 ANNOTATION 3.2 ANNOTATION PLANE 3.3 ASSEMBLY MODEL 3.4 ASSOCIATED ENTITY 3.5 ASSOCIATED GROUP 3.6 ASSOCIATIVITY 3.7 ATTRIBUTE 3.8 COORDINATE SYSTEM 3.9 DATA 3.10 DATUM SYSTEM 3.11 DERIVATIVE 3.12 DESIGN MODEL 3.13 DIGITAL ELEMENT 3.14 DIGITAL ELEMENT IDENTIFIER 3.15 DIRECTION-DEPENDENT TOLERANCE 3.16 DRAWING GRAPHIC SHEET 3.17 GEOMETRIC ELEMENT
15	3.18 HARD COPY 3.19 INSTALLATION MODEL 3.20 MANAGEMENT DATA 3.21 MODEL 3.22 MODEL GEOMETRY 3.23 MODEL VALUE 3.24 PRODUCT DEFINITION DATA 3.25 PRODUCT DEFINITION DATA SET 3.26 QUERY 3.27 REPRESENTED LINE ELEMENT 3.28 RESOLVED DIMENSION 3.29 SAVED VIEW 3.30 SPECIAL CHARACTER 3.31 SUPPLEMENTAL GEOMETRY
16	Section 4 Data Set Identification and Control 4.1 GENERAL 4.1.1 Data Set Identifier 4.1.2 Drawing Graphic Sheet Identification 4.1.3 Associated List Identification 4.1.4 Part or Identifying Number 4.2 RELATED DATA 4.3 DATA MANAGEMENT 4.3.1 Management System 4.3.2 Approval 4.3.3 Storage and Retention 4.3.4 Revision History
18	Section 5 Data Set Requirements 5.1 GENERAL MODEL REQUIREMENTS 5.1.1 Design Model Requirement 5.1.2 Associativity 5.1.3 Coordinate Systems 5.1.4 Applications of Supplemental Geometry 5.1.5 Part Features Not Fully Modeled 5.1.6 Assembly Model Completeness 5.1.7 Installation Model Completeness 5.2 GENERAL METHOD REQUIREMENTS
20	5.2.1 Model Only 5.2.2 Model and Drawing Graphic Sheet 5.3 MANAGEMENT DATA 5.3.1 Management Data in the Data Set 5.3.2 Management Data on a Model 5.4 SECURITY MARKING 5.4.1 Location of Security Marking on Models
21	5.4.2 Government, Department of Defense, and Other Federal Agencies Security Marking 5.4.3 Company Security Marking 5.4.4 Government Notices, Statements, and Legends 5.5 VIEWS ON MODELS
22	Section 6 Design Model Requirements 6.1 GENERAL 6.1.1 Geometric Scale, Units, and Precision 6.1.2 Design Model Completeness
23	Section 7 Common Requirements for Models and Drawing Graphics Sheets 7.1 COMMON REQUIREMENTS 7.1.1 Display Management 7.1.2 Hard Copy 7.1.3 Leader Lines 7.2 MODEL REQUIREMENTS 7.2.1 Associativity 7.2.2 Attributes 7.2.3 Annotation Planes
24	7.2.4 Leader and Extension Lines 7.2.5 Direction-Dependent Tolerances 7.2.6 Indicating Limited Application of a Tolerance 7.2.7 Query
25	7.3 DRAWING GRAPHIC SHEET REQUIREMENTS 7.3.1 Annotation in Axonometric Views
39	Section 8 Notes and Special Notations 8.1 COMMON REQUIREMENTS 8.2 MODEL REQUIREMENTS 8.2.1 Notes Area Annotation Plane 8.2.2 General Notes 8.2.3 Local Notes 8.2.4 Flag Notes 8.2.5 Special Notations 8.3 DRAWING GRAPHIC SHEET REQUIREMENTS 8.3.1 Local Notes in Axonometric Views
40	Section 9 Model Values and Dimensions 9.1 COMMON REQUIREMENTS 9.1.1 Resolved Dimensions 9.2 MODEL REQUIREMENTS 9.2.1 Basic Dimensions
41	9.2.2 Size Dimensions 9.3 DRAWING GRAPHIC SHEET REQUIREMENTS 9.3.1 Presentation of Dimensions in Axonometric Views
45	Section 10 Plus and Minus Tolerances 10.1 COMMON REQUIREMENTS 10.2 MODEL REQUIREMENTS 10.2.1 Chamfers 10.2.2 Depth Specification 10.3 DRAWING GRAPHIC SHEET REQUIREMENTS
51	Section 11 Datum Applications 11.1 COMMON REQUIREMENTS 11.2 MODEL REQUIREMENTS 11.2.1 Datum Reference Frames and Coordinate Systems 11.2.2 Identification of Datum Features
52	11.2.3 Datum Target Identification and Attachment 11.2.4 Multiple Features Establishing a Datum 11.3 DRAWING GRAPHIC SHEET REQUIREMENTS
66	Section 12 Geometric Tolerances 12.1 COMMON REQUIREMENTS 12.2 MODEL REQUIREMENTS 12.2.1 Form Tolerances 12.2.2 Orientation Tolerances 12.2.3 Profile Tolerances
67	12.2.4 Location Tolerances 12.2.5 Runout Tolerances 12.3 DRAWING GRAPHIC SHEET REQUIREMENTS 12.3.1 Requirements Applicable to all Geometric Tolerances 12.3.2 Form Tolerances 12.3.3 Orientation Tolerances
68	12.3.4 Profile Tolerances 12.3.5 Position Tolerances 12.3.6 Runout Tolerances on a Drawing Graphic Sheet
107	MANDATORY APPENDIX I 1.9.1 Definitions 3.6 Views on Models 5.3.1 Orthographic Views. 5.3.2 Axonometric Views.