BS EN 61236:1995:2002 Edition
$189.07
Saddles, pole clamps (stick clamps) and accessories for live working
| Published By | Publication Date | Number of Pages |
| BSI | 2002 | 46 |
Covers dimensional and mechanical characteristics with corresponding mechanical tests including check items (visual, functional marking etc).
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | BRITISH STANDARD |
| 2 | Committees responsible for this British�Standard |
| 3 | Contents |
| 6 | Foreword Contents |
| 9 | Section 1 General 1.1 Scope 1.2 Normative references 1.3 Definitions 1.3.1 Terms defined in accordance with IEC�60050(151) and IEC�61318 1.3.1.1 type test 1.3.1.2 routine test 1.3.1.3 sampling test 1.3.1.4 acceptance test 1.3.1.5 rated value |
| 10 | 1.3.1.6 minor defect 1.3.1.7 major defect 1.3.1.8 critical defect 1.3.2 Definition of special terms 1.3.2.1 type of tool 1.3.2.2 family of tools 1.3.2.3 MICDT (minor defect control test) 1.3.2.4 MADCT (major defect control test) 1.3.2.5 1.3.2.6 1.3.2.7 1.3.2.8 |
| 11 | Section 2 Technical characteristics 2.1 General 2.2 Dimensional and mechanical characteristics 2.2.1 Dimensional characteristics 2.2.2 Mechanical characteristics 2.3 Corrosion protection Table 1 Mechanical characteristics for each type of tool |
| 13 | Section 3 Type tests 3.1 General 3.2 Visual and functional inspection 3.3 Dimensional check 3.4 Mechanical tests — General test conditions and results Table 2 General test information |
| 14 | 3.5 Mechanical tests — Particular requirements 3.5.1 Locking device with chain or strap 3.5.2 Chain binder 3.5.3 Ring saddle with rigid bracket |
| 15 | 3.5.4 Ring saddle with chain bracket 3.5.5 Lift-type saddle 3.5.6 Pole-type saddle 3.5.7 Saddle extension 3.5.8 Tower-type saddle |
| 16 | 3.5.9 Crossarm-type saddle 3.5.10 Block saddle 3.5.11 Tower-arm yoke 3.5.12 Platform pivot attachment 3.5.13 Saddles and accessories for hydraulic tension puller |
| 17 | 3.5.14 Pole clamp (stick clamp) |
| 18 | 3.5.15 Support-pole stirrup (wire-tong stirrup) 3.5.16 Offset eye |
| 19 | Section 4 Sampling tests and routine tests 4.1 Sampling tests 4.2 Routine tests 4.2.1 Visual inspection 4.2.2 Operation |
| 21 | Section 5 Special clauses 5.1 Marking 5.2 Modifications 5.3 Acceptance tests 5.4 Quality assurance plan |
| 23 | Annex A (normative) Acceptance tests Annex B (normative) General test procedure Table B.1 – Example of a test sequence for tower-type saddle |
| 26 | Annex C (normative) Sampling procedure C.1 General C.2 Sampling plan Table C.1 Sampling plan |
| 45 | Annex ZA (normative) Normative references to international publications with their corresponding European … |
