ISO 2808:2007
$46.15
Paints and varnishes — Determination of film thickness
| Published By | Publication Date | Number of Pages |
| ISO | 2007-02 | 46 |
ISO 2808:2007 describes a number of methods that are applicable to the measurement of the thickness of coatings applied to a substrate. Methods for determining wet-film thickness, dry-film thickness and the film thickness of uncured powder layers are described. Reference is made to individual standards where these exist. Otherwise the method is described in detail.
The standard also defines terms concerning the determination of film thickness.
Related products
-
BS ISO 22754:2008 2009
Pulp and paper. Determination of the effective residual ink concentration (ERIC number) by infrared reflectance…
-
BS ISO 6488:2004 2008
Tobacco and tobacco products. Determination of water Content. Karl Fischer method Published By Publication Date…
-
BS ISO 8943:2007 2008
Refrigerated light hydrocarbon fluids. Sampling of liquefied natural gas. Continuous and intermittent methods Published By…
-
BS ISO 25620:2008 2009
Laminate floor coverings. Determination of long-side friction for mechanically assembled panels Published By Publication Date…
-
BS ISO 22856:2008 2009
Equipment for crop protection. Methods for the laboratory measurement of spray drift. Wind tunnels Published…
-
AS/NZS ISO 2801:2008 (R2016)
Clothing for protection against heat and flame – General recommendations for selection, care and use…
-
BS ISO 20665:2008 2009
Water quality. Determination of chronic toxicity to Ceriodaphnia dubia Published By Publication Date Number of…
-
BS ISO 26243:2007 2008
Cards for staple fibres spinning. Vocabulary and principles of construction Published By Publication Date Number…
-
BS ISO 23559:2007 2008
Plastics. Film and sheeting. Guidance on the testing of thermoplastic films Published By Publication Date…
-
BS ISO 22662:2007 2008
Milk and milk products. Determination of lactose content by high-performance liquid chromatography (Reference method) Published…
-
BS ISO 7789:2007 2008
Hydraulic fluid power. Two-, three- and four-port screw-in cartridge valves. Cavities Published By Publication Date…
-
BS ISO 9895:2008 2009
Paper and board. Compressive strength. Short-span test Published By Publication Date Number of Pages BSI…
-
BS ISO 4960:2007 2008
Cold-reduced carbon steel strip with a mass fraction of carbon over 0,25 % Published By…
-
BS EN ISO 2808:2007
Paints and varnishes. Determination of film thickness Published By Publication Date Number of Pages BSI…
-
BS ISO 6396:2008 2009
Earth-moving machinery. Determination of emission sound pressure level at operator’s position. Dynamic test conditions Published…
-
BS ISO 6780:2003 2008
Flat pallets for intercontinental materials handling. Principal dimensions and tolerances Published By Publication Date Number…
-
BS ISO 23868:2008 2009
Document management. Monitoring and verification of information stored on 130mm optical media Published By Publication…
-
BS ISO 30042:2008 2009
Systems to manage terminology, knowledge and content. TermBase eXchange (TBX) Published By Publication Date Number…
-
BS ISO 2836:2004 2008
Graphic technology. Prints and printing inks. Assessment of resistance to various agents Published By Publication…
-
BS ISO 9588:2007 2008
Metallic and other inorganic coatings. Post-coating treatments of iron or steel to reduce the risk…
-
BS ISO 3245:2007 2008
Rolling bearings. Needle roller bearings, drawn cup without inner ring. Boundary dimensions and tolerances Published…
-
BS ISO 8568:2007 2008
Mechanical shock. Testing machines. Characteristics and performance Published By Publication Date Number of Pages BSI…
-
ISO 22007-2:2008
Plastics — Determination of thermal conductivity and thermal diffusivity — Part 2: Transient plane heat…
-
ISO/TS 10303-1007:2008
Industrial automation systems and integration — Product data representation and exchange — Part 1007: Application…
-
BS ISO 4700:2007 2008
Iron ore pellets for blast furnace and direct reduction feedstocks. Determination of the crushing strength…
-
BS ISO 26603:2008 2009
Plastics. Aromatic isocyanates for use in the production of polyurethanes. Determination of total chlorine Published…
-
BS ISO 4226:2007 2008
Air quality. General aspects. Units of measurement Published By Publication Date Number of Pages BSI…
-
BS ISO 3976:2006 2008
Milk fat. Determination of peroxide value Published By Publication Date Number of Pages BSI 2008…
-
BS ISO 22889:2007 2008
Metallic materials. Method of test for the determination of resistance to stable crack extension using…
-
BS ISO 24535:2007 2008
Intelligent transport systems. Automatic vehicle identification. Basic electronic registration identification (Basic ERI) Published By Publication…
-
BS ISO 6395:2008 2009
Earth-moving machinery. Determination of sound power level. Dynamic test conditions Published By Publication Date Number…
-
ISO 22007-4:2008
Plastics — Determination of thermal conductivity and thermal diffusivity — Part 4: Laser flash method…
-
BS ISO 633:2007 2008
Cork. Vocabulary Published By Publication Date Number of Pages BSI 2008 42
-
BS ISO 3852:2007 2008
Iron ores for blast furnace and direct reduction feedstocks. Determination of bulk density Published By…
-
BS ISO 20280:2007 2008
Soil quality. Determination of arsenic, antimony and selenium in aqua regia soil extracts with electrothermal…
-
BS ISO 8468:2007 2008
Ships and marine technology. Ship’s bridge layout and associated equipment. Requirements and guidelines Published By…
-
BS ISO 860:2007 2008
Terminology work. Harmonization of concepts and terms Published By Publication Date Number of Pages BSI…
-
ISO 22007-3:2008
Plastiques — Détermination de la conductivité thermique et de la diffusivité thermique — Partie 3:…
-
BS ISO 22555:2007 2008
Ships and marine technology. Propeller pitch indicators Published By Publication Date Number of Pages BSI…
-
BS ISO 22554:2007 2008
Ships and marine technology. Propeller shaft revolution indicators. Electric type and electronic type Published By…
