{"id":275333,"date":"2024-10-19T18:31:04","date_gmt":"2024-10-19T18:31:04","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/bs-en-62135-22015\/"},"modified":"2024-10-25T14:55:48","modified_gmt":"2024-10-25T14:55:48","slug":"bs-en-62135-22015","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/bsi\/bs-en-62135-22015\/","title":{"rendered":"BS EN 62135-2:2015"},"content":{"rendered":"

This part of IEC 62135<\/span> <\/span> is applicable to equipment for resistance welding and allied processes which are connected to mains supplies with rated voltages up to 1 000 V a.c. r.m.s. This standard does not define safety requirements.<\/p>\n

Resistance welding equipment type tested in accordance with, and which has met the requirements of, this standard, is deemed to be in compliance for all applications.<\/p>\n

The frequency range covered is from 0 Hz to 400 Ghz.<\/p>\n

This product EMC standard for resistance welding equipment takes precedence over all aspects of the generic standards and no additional EMC tests are required or necessary.<\/p>\n

\n
\n NOTE 1\n <\/div>\n

Typical allied processes are resistance hard and soft soldering or resistance heating achieved by means comparable to resistance welding equipment.<\/p>\n<\/div>\n

\n
\n NOTE 2\n <\/div>\n

Limit values are specified for only part of the frequency range.<\/p>\n<\/div>\n

Resistance welding equipment are classified as class A and class B equipment.<\/p>\n

This part of IEC 62135<\/span> <\/span> specifies<\/p>\n

    \n
  1. \n

    test methods to be used in conjunction with CISPR 11<\/span> <\/span> to determine radiofrequency (RF) emission;<\/p>\n<\/li>\n

  2. \n

    relevant standards and test methods for harmonic current emission, voltage fluctuation and flicker.<\/p>\n<\/li>\n<\/ol>\n

    \n
    \n NOTE 3\n <\/div>\n

    The limits in this standard cannot, however, provide full protection against interference to radio and television reception when the resistance welding equipment is used closer than 30 m to the receiving antenna(e).<\/p>\n<\/div>\n

    \n
    \n NOTE 4\n <\/div>\n

    In special cases, when highly susceptible apparatus is being used in close proximity, additional mitigation measures are sometimes employed to further reduce the electromagnetic emissions.<\/p>\n<\/div>\n

    This part of IEC 62135<\/span> <\/span> also defines immunity requirements and test methods for continuous and transient, conducted and radiated disturbances including electrostatic discharges.<\/p>\n

    \n
    \n NOTE 5\n <\/div>\n

    These requirements do not, however, cover extreme cases which are extremely rare.<\/p>\n<\/div>\n

    PDF Catalog<\/h4>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
    PDF Pages<\/th>\nPDF Title<\/th>\n<\/tr>\n
    8<\/td>\nEnglish
    CONTENTS <\/td>\n<\/tr>\n
    10<\/td>\nFOREWORD <\/td>\n<\/tr>\n
    12<\/td>\n1 Scope
    2 Normative references <\/td>\n<\/tr>\n
    14<\/td>\n3 Terms and definitions <\/td>\n<\/tr>\n
    15<\/td>\n4 General test requirements
    4.1 Test conditions
    4.2 Measuring instruments
    4.3 Artificial mains network
    4.4 Voltage probe
    4.5 Antennas
    5 Test set-up for emission and immunity
    5.1 General requirements <\/td>\n<\/tr>\n
    16<\/td>\n5.2 Ancillary equipment
    6 Emission tests
    6.1 Classification of equipment
    Figures
    Figure 1 \u2013 Test position for H field measurement <\/td>\n<\/tr>\n
    17<\/td>\n6.2 Test conditions <\/td>\n<\/tr>\n
    18<\/td>\n6.3 Emission limits <\/td>\n<\/tr>\n
    19<\/td>\n7 Immunity tests
    7.1 Tests applicability <\/td>\n<\/tr>\n
    20<\/td>\n7.2 Test conditions
    7.3 Immunity performance criteria <\/td>\n<\/tr>\n
    21<\/td>\n7.4 Immunity levels
    Tables
    Table 1 \u2013 Immunity levels \u2013 Enclosure
    Table 2 \u2013 Immunity levels \u2013 AC input power port <\/td>\n<\/tr>\n
    22<\/td>\n8 Documentation for the purchaser\/user
    Table 3 \u2013 Immunity levels \u2013 Ports for measurement and control <\/td>\n<\/tr>\n
    24<\/td>\nAnnex A (informative) Limits
    A.1 General
    A.2 Mains terminal disturbance voltage limits
    A.3 Electromagnetic radiation disturbance limits
    Table A.1 \u2013 Mains terminal disturbance voltage limits, idle state
    Table A.2 \u2013 Mains terminal disturbance voltage limits, load conditions <\/td>\n<\/tr>\n
    25<\/td>\nTable A.3 \u2013 Electromagnetic radiation disturbance limits, idle state
    Table A.4 \u2013 Electromagnetic radiation disturbance limits, load conditions <\/td>\n<\/tr>\n
    26<\/td>\nA.4 Harmonic current limits
    Table A.5 \u2013 Magnetic field emission limits for Class B equipment
    Table A.6 \u2013 Maximum permissible harmonic current for
    \nequipment with input current I1cc \u2264 16 A <\/td>\n<\/tr>\n
    27<\/td>\nTable A.7 \u2013 Current emission limits for equipment with 16 A < I1cc \u2264 75 A
    \nother than balanced three-phase equipment
    Table A.8 \u2013 Current emission limits for
    \nbalanced three-phase equipment with input current 16 A < I1cc \u2264 75 A
    Table A.9 \u2013 Current emission limits for balanced three-phase equipment
    \nwith input current 16 A < I1cc \u2264 75 A under specified conditions <\/td>\n<\/tr>\n
    28<\/td>\nA.5 Limits for voltage fluctuations and flicker
    Table A.10 \u2013 Current emission limits for balanced three-phase equipment
    \nwith I1cc \u2264 75 A under specified conditions (d, e, f) <\/td>\n<\/tr>\n
    29<\/td>\nTable A.11 \u2013 Limits for resistance welding equipment I1cc \u2264 75 A <\/td>\n<\/tr>\n
    30<\/td>\nAnnex B (informative) Symbols
    Table B.1 \u2013 Symbols to describe EMC properties <\/td>\n<\/tr>\n
    31<\/td>\nBibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":"

    Resistance welding equipment – Electromagnetic compatibility (EMC) requirements<\/b><\/p>\n\n\n\n\n
    Published By<\/td>\nPublication Date<\/td>\nNumber of Pages<\/td>\n<\/tr>\n
    BSI<\/b><\/a><\/td>\n2015<\/td>\n34<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":275338,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[2641],"product_tag":[],"class_list":{"0":"post-275333","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-bsi","8":"first","9":"instock","10":"sold-individually","11":"shipping-taxable","12":"purchasable","13":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/275333","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/275338"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=275333"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=275333"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=275333"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}